Parts for 40 HP EFI 4 Cyl 4-Stroke Mercury Outboard Motor Gear Housing Driveshaft - 2.33:1 Gear Ratio
Reference numbers in this diagram can be found in a light blue row below — scroll down to order.
| #- | 8M0118187 | GC SEAPRO L LONG SeaPro Only (1 required per assembly) |
|
16008M0118187 - GC SEAPRO L LONG [ More info ] Unavailable |
||
| #- | 8M0118186 | GC 40-60 LG (1 required per assembly) |
|
16008M0118186 - GC 40-60 LG [ More info ] Unavailable |
||
| #- | 8M0118188 | GC SEAPRO X LONG (1 required per assembly) |
|
16008M0118188 - GC SEAPRO X LONG [ More info ] Unavailable |
||
| #- | 816575A2 | SEAL KIT (1 required per assembly) |
| #- | 43035A05 | SEAL KIT-G/H (1 required per assembly) |
| #- | 8M0113801 | REPAIR KIT- W/P (1 required per assembly) |
| #- | 8M0100526 | REPAIR KIT - IMP (1 required per assembly) |
|
18-3214 - Impeller Repair Kit, Without Housing [ More info ] |
||
|
46-01811 - Water Pump Kit without Housing 47-43026T11, Q06 [ More info ] |
||
| #- | 803496T2 | REPAIR KIT (1 required per assembly) |
| #1 | 8M0118594 | GEAR HOUSING ASSEMBLY BASIC (1 required per assembly) |
| #2 | 8M0084244 | PIN DOWEL FRONT (1 required per assembly) |
| #3 | 43046 | TUBE OILER (1 required per assembly) |
| #4 | 8M0058389 | SCREW KIT DRAIN Magnetic (3 required per assembly) |
|
22-8M0058389 - Screw Kit - Priced Individually [ More info ] |
||
| #5 | 8M0204693 | SEAL @6 (3 required per assembly) — Replaces: 830749 |
|
26-8M0204693 - Drain Screw Washer, Priced Individually [ More info ] |
||
| #6 | 43044 | PIN DOWEL - WITHOUT HOLE (.375 X .625) REAR (1 required per assembly) |
| #7 | 31640T07 | TRIM TAB (1 required per assembly) |
|
31640T07 - Trim Tab [ More info ] Unavailable |
||
| #8 | 825427 | SCREW (.437-14 X 1.250) STAINLESS STEEL (1 required per assembly) |
| #9 | 451761 | WASHER (.453 X .812 X .105) BLACK OXIDE (1 required per assembly) |
| #10 | 43040T1 | CARRIER ASSEMBLY (1 required per assembly) |
| #11 | NSS | NOT SOLD SEPARATE NEEDLE BEARING (1 required per assembly) |
|
NSS - NOT SOLD SEPARATE [ More info ] Unavailable |
||
| #12 | 826134Q | ANODE (2 required per assembly) |
|
97-826134Q - Anode, Aluminum, Outboard Side Pocket, Priced Individually [ More info ] |
||
|
97-826134T - Anode - Outboard Side Pocket - Priced Individually [ More info ] |
||
| #13 | 401386 | NUT (M6) STAINLESS STEEL (1 required per assembly) |
| #14 | 4000333 | SCREW (M6 X 40) (1 required per assembly) |
| #15 | NSS | NOT SOLD SEPARATE PINION GEAR - PART OF FORWARD GEAR KIT (1 required per assembly) |
| #16 | 35921 | NUT (.625-18) (1 required per assembly) |
|
18-2359 - Nut Kit [ More info ]
|
||
| #17 | 883047A1 | BEARING ASSEMBLY TAPERED ROLLER (1 required per assembly) |
| #18 | 8M0063265 | SHIM SET (1 required per assembly) |
| #19 | 8M0118189 | DRIVESHAFT ASSEMBLY LL SeaPro Only (1 required per assembly) |
| #19 | 859105A1 | DRIVESHAFT ASSEMBLY (Long) (1 required per assembly) |
|
92-205-04-20G - Drive Shaft replaces 45-859105A 1 [ More info ] |
|
| #19 | 875222A1 | DRIVESHAFT ASSEMBLY (X-Long) (1 required per assembly) |
|
92-205-04-25G - Drive Shaft replaces 45-875222A 1 [ More info ] |
|
| #20 | 42461A1 | SLEEVE/RING KIT (1 required per assembly) |
| #21 | NSS | NOT SOLD SEPARATE RING-SEAL (1 required per assembly) |
| #22 | 8M0113262 | COVER ASSEMBLY WATER PUMP (1 required per assembly) |
| #23 | 8M0142616 | GASKET FACE PLATE TO GEARCASE (1 required per assembly) — Replaces: 8M0050720, 8M0112903 |
| #24 | 430472 | GASKET (1 required per assembly) |
|
27-43047 2 - Gasket [ More info ] Unavailable |
||
| #25 | 43035 | SEAL OIL UPPER (1 required per assembly) |
|
18-0583 - Seal, 26-43035 [ More info ]
|
||
|
26-8M0245495 - OIL SEAL [ More info ] Unavailable |
||
| #26 | 43036 | SEAL OIL LOWER (1 required per assembly) |
| #27 | 8172771 | GASKET (1 required per assembly) |
| #28 | 817275A2 | HOUSING KIT UPPER WATER PUMP (1 required per assembly) |
| #29 | 8M0204709 | FACEPLATE-W/P (1 required per assembly) — Replaces: 8172761 |
| #30 | 82684430 | SCREW (M6 X 30) (4 required per assembly) |
| #31 | 8M0151044 | COUPLING WATER TUBE (1 required per assembly) — Replaces: 8M0109700 |
| #32 | 8M0204723 | KEY @2 (1 required per assembly) — Replaces: 8M0032833 |
| #33 | 43026T2 | IMPELLER (1 required per assembly) |
| #34 | 82684425 | SCREW (M6 X 25) (6 required per assembly) |
| #35 | 8M0142851 | VRING FACE SEAL (1 required per assembly) — Replaces: 8M2014338 |
| #36 | 8M0118190 | SHIFT SHAFT ASSEMBLY LOWER, LL SeaPro Only (1 required per assembly) |
| #36 | 884563A00 | SHIFT SHAFT ASSEMBLY (Long) (1 required per assembly) |
| #36 | 884565A00 | SHIFT SHAFT ASSEMBLY (X-Long) (1 required per assembly) |
| #37 | 29641 | E RING (1 required per assembly) |
| #38 | 43052A4 | BUSHING ASSEMBLY (1 required per assembly) |
| #39 | 8M0204681 | O RING @5 (1 required per assembly) — Replaces: 457101 |
|
25-8M0204681 - O RING Note: Priced Individually [ More info ] |
||
| #40 | 8M0204708 | SEAL (1 required per assembly) — Replaces: 8164641 |
| #41 | 82684425 | SCREW (M6 X 25) (2 required per assembly) |
| #42 | 891637 | BUSHING (1 required per assembly) |
| #NS | NSS | NOT SOLD SEPARATE TOOL, FACE SEAL SETTING (1 required per assembly) |






