Parts for 50 (3 Cyl.) 2-Stroke Carbureted Mercury Outboard Motor Gear Hsg Driveshaft-60 Sea / Mara / Big Foot-6 Jaw Rev. Clutch
Reference numbers in this diagram can be found in a light blue row below — scroll down to order.
| #- | 9011G92 | GC 60 3CYL 2S LG (LONG) BLACK (1 required per assembly) — Replaces: 9011G16, 9011G45 |
|
1667-9011G92 - Gear Housing Assembly (complete) [ More info ] Unavailable |
||
|
90-205-B20M - SE205 Lower Unit Mercury 3 and 4 Cylinder, 2.33 to 1, Big Foot, 50-60HP, 20 Inch [ More info ] |
|
| #- | 9011G94 | GC 60 BF LL-BLK (LL) BLACK (1 required per assembly) — Replaces: 9011G14, 9011G47 |
|
1667-9011G94 - Gear Housing Assembly [ More info ] Unavailable |
||
| #- | 9011G96 | ORD 1667-9011G92 (LONG) GRAY (1 required per assembly) — Replaces: 9011G17, 9011G46 |
|
1667-9011G96 - Ord 1667-9011G92 [ More info ] Unavailable |
||
| #- | 9011G48 | GEAR HOUSING (LL) GRAY (1 required per assembly) — Replaces: 9011G15 |
|
1667-9011G48 - GEAR Housing, NLA [ More info ] Unavailable |
||
| #- | 8M0113799 | REPAIR KIT-W/P (1 required per assembly) — Replaces: 43024A7 |
| #- | 43035A4 | SEAL KIT (1 required per assembly) |
| #1 | 9011G59 | GEAR HOUSING ASSEMBLY BASIC (BASIC) (GRAY) (1 required per assembly) — Replaces: 9011G8, 9011G9, 9011G60 |
| #2 | 8M0084244 | PIN DOWEL (FRONT) (1 required per assembly) — Replaces: 43043 |
| #3 | 43046 | TUBE OILER (1 required per assembly) |
| #4 | 79953Q04 | SCREW KIT DRAIN (2 required per assembly) — Replaces: 79953A2, 79953Q2 |
|
10-79953K04 - Drain Screw - Priced Individually [ More info ] |
||
| #5 | 67892A06 | PLUG KIT DRAIN - MAGNETIC (1 required per assembly) — Replaces: 67892A1, 67892A05 |
|
22-67892A06 - Drain Plug Kit [ More info ] Unavailable |
||
|
22-8M0058389 - Screw Kit - Priced Individually [ More info ] |
||
| #6 | 191833 | SEAL (3 required per assembly) — Replaces: 19183, 191832 |
|
12-19183 3 - Seal -Blue - Priced Individually [ More info ] Unavailable |
||
|
12-19183Q02 - Seals, Pack of 4 (yes this is actually a pack of 4) [ More info ] |
||
| #7 | 43044 | PIN DOWEL - WITHOUT HOLE (.375 X .625) (REAR) (1 required per assembly) |
| #8 | 31640T07 | TRIM TAB (1 required per assembly) — Replaces: 316405, 31640T5 |
|
31640T07 - Trim Tab [ More info ] Unavailable |
||
| #9 | 825427 | SCREW (.437-14 X 1.250) STAINLESS STEEL (1 required per assembly) |
| #10 | 45176 | WASHER (.453 X .812 X .105) STAINLESS STEEL (1 required per assembly) |
| #11 | 43040T1 | CARRIER ASSEMBLY (1 required per assembly) — Replaces: 43040A1 |
| #12 | NSS | NOT SOLD SEPARATE NEEDLE BEARING (1 required per assembly) |
|
NSS - NOT SOLD SEPARATE [ More info ] Unavailable |
||
| #13 | 826134Q | ANODE (2 required per assembly) — Replaces: 826134 |
|
97-826134Q - Anode, Aluminum, Outboard Side Pocket, Priced Individually [ More info ] |
||
|
97-826134T - Anode - Outboard Side Pocket - Priced Individually [ More info ] |
||
| #14 | 401386 | NUT (M6) STAINLESS STEEL (1 required per assembly) — Replaces: 8268336, 40144 |
| #15 | 4000333 | SCREW (M6 X 40) (1 required per assembly) |
| #16 | 44484T | GEAR PINION (13 TEETH) (ALSO PART OF 43-850033A2) (1 required per assembly) — Replaces: 44484 |
| #17 | 35921 | NUT (.625-18) (1 required per assembly) |
|
18-2359 - Nut Kit [ More info ]
|
||
| #18 | 850307 | CAM SHIFT CONTROL (1 required per assembly) |
| #19 | 42677A1 | BEARING ASSEMBLY TAPERED ROLLER (1 required per assembly) |
| #20 | 8M0063265 | SHIM SET (AR required per assembly) — Replaces: 44492A1 |
| #21 | 826736A1 | DRIVESHAFT ASSEMBLY (LONG) (1 required per assembly) |
|
92-205-04-20H - Drive Shaft replaces 45-826736A 1 [ More info ] |
|
| #21 | 826737A1 | DRIVESHAFT ASSEMBLY (LL) (1 required per assembly) |
| #22 | 42461A1 | SLEEVE/RING KIT (1 required per assembly) |
| #23 | NSS | NOT SOLD SEPARATE RING SEAL (1 required per assembly) |
| #24 | 8M0113262 | COVER ASSEMBLY WATER PUMP (1 required per assembly) — Replaces: 43055A4 |
| #25 | 430331 | GASKET (1 required per assembly) |
| #26 | 430472 | GASKET (1 required per assembly) |
|
27-43047 2 - Gasket [ More info ] Unavailable |
||
| #27 | 43035 | SEAL OIL (UPPER) (1 required per assembly) |
|
26-8M0245495 - OIL SEAL [ More info ] Unavailable |
||
| #28 | 43036 | SEAL OIL (LOWER) (1 required per assembly) |
| #29 | 8172771 | GASKET (1 required per assembly) — Replaces: 817277 |
| #30 | 817275A2 | HOUSING KIT UPPER WATER PUMP (1 required per assembly) |
| #31 | 8M0204709 | FACEPLATE-W/P (1 required per assembly) — Replaces: 817276, 8172761 |
| #32 | 8248327 | SCREW (M6 X 30) (4 required per assembly) |
|
10-824832 7 - Screw [ More info ] Unavailable |
||
| #33 | 826763A1 | COUPLING (LONG) (1 required per assembly) |
| #33 | 826762A1 | COUPLING (LL) (1 required per assembly) |
| #34 | 8M0204723 | KEY @2 (1 required per assembly) — Replaces: 43037, 8M0032833 |
| #35 | 43026T2 | IMPELLER (1 required per assembly) — Replaces: 430262 |
| #36 | 8248326 | SCREW (M6 X 25 MM) (6 required per assembly) |
| #37 | 853906A1 | SHIFT SHAFT ASSEMBLY (LONG) (1 required per assembly) |
| #37 | 853907A1 | SHIFT SHAFT ASSEMBLY (LL) (1 required per assembly) |
| #38 | 29641 | E RING (1 required per assembly) |
| #39 | 43052A4 | BUSHING ASSEMBLY (1 required per assembly) |
| #40 | 8M0204681 | O RING @5 (1 required per assembly) — Replaces: 45710, 457101 |
|
25-8M0204681 - O RING Note: Priced Individually [ More info ] |
||
| #41 | 8M0204708 | SEAL (1 required per assembly) — Replaces: 8164641 |
| #42 | 8248326 | SCREW (M6 X 25 MM) (2 required per assembly) |






