1399-07359 - VRO Replacement Fuel Pump, 90 Degree Blocks Only,See Detail page for additional info
|
  |
Your Price
$0.00
Part Number
1399-07359
Manufacturer
Engineered Marine Products
Replaces OEM 5007420.
1399-07359 - VRO Replacement non-oiling Fuel Pump, Requires Pre-Mixing of Fuel and Oil.
ONLY for use only on engines with 90 degree angle cylinder block. (90 degree = Pistons pointing at a right angle like the letter L.) Good for 90HP - 250HP V4 and V6 Crossflow and Looper engines. Crossflow engines have shaped piston tops, Looper engines have flat top pistons. On 90 degree engines the VRO is mounted using a separate standalone bracket. (See image below.)
NOT to be used on 60 degree angle cylinder blocks. (60 degree = pistons at less than a right angle, more like the letter V.) If your motor cover has LOUVER VENTS it is a 60 degree block and will NOT work with this pump. On 60 degree engines the VRO is mounted to the Vapor Recovery Tank assembly. (See image below.)
Not for use on three cylinder motors.
TIP: See the TECH INFO link above for additional 90 degree vs 60 degree details. You can also check the Cylinder & Crankcase diagram and view the Powerhead Gasket Set part number. The gasket set detail page may specify if it is for a 90 or 60 degree block.
PLEASE INCLUDE YOUR MODEL NUMBER in the comments section at checkout so we can confirm the application prior to shipment. Please say "Confirm Model _______" or similar.
This a Pre-Mix VRO Conversion Fuel Pump Kit. It is manufactured by EMP for use on Johnson and Evinrude applications to replace the original VRO fuel pump and mix your own fuel and oil in the fuel tank instead.
No wiring is required. Please see the TECH INFO link for instructions. You will need to notch the mounting bracket as shown in the instructions.
This is an excellent replacement pump at a very affordable price.
Engineered Marine Products is a leading supplier of aftermarket parts for marine engines including outboard, inboard and stern drive.
Replaces OEM 5007420.1399-07359 - VRO Replacement non-oiling Fuel Pump, Requires Pre-Mixing of Fuel and Oil.ONLY for use only on engines with 90 degree angle cylinder block. (90 degree = Pistons pointing at a right angle like the letter L.) Good for 90HP - 250HP V4 and V6 Crossflow and Looper engines. Crossflow engines have shaped piston tops, Looper engines have flat top pistons. On 90 degree engines the VRO is mounted using a separate standalone bracket. (See image below.)NOT to be used on 60 degree angle cylinder blocks. (60 degree = pistons at less than a right angle, more like the letter V.) If your motor cover has LOUVER VENTS it is a 60 degree block and will NOT work with this pump. On 60 degree engines the VRO is mounted to the Vapor Recovery Tank assembly. (See image below.)Not for use on three cylinder motors.TIP: See the TECH INFO link above for additional 90 degree vs 60 degree details. You can also check the Cylinder and Crankcase diagram and view the Powerhead Gasket Set part number. The gasket set detail page may specify if it is for a 90 or 60 degree block. PLEASE INCLUDE YOUR MODEL NUMBER in the comments section at checkout so we can confirm the application prior to shipment. Please say "Confirm Model _______" or similar. This a Pre-Mix VRO Conversion Fuel Pump Kit. It is manufactured by EMP for use on Johnson and Evinrude applications to replace the original VRO fuel pump and mix your own fuel and oil in the fuel tank instead. No wiring is required. Please see the TECH INFO link for instructions. You will need to notch the mounting bracket as shown in the instructions. This is an excellent replacement pump at a very affordable price.
0.00
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.