Logo
FULL SITE MENU

Recent content by bryane

  1. B

    200 verado warning lights

    This is the way I connected the fuel tank there was no black/orange wire on the pink/black wire in the kit.
  2. B

    200 verado warning lights

    Hello Started out with vent SW Hi Stbd engine light on and after using it to see it it comes back on after draining the hose and float has many warnings maybe all related? Driver Power Lo Cntr engine-MPRLY output Cntr engine-ETC Sticking Cntr Engine-ETC Control Cntr Engine all saved. That's a...
  3. B

    2001 Pro max 300

    Just had a powerhead installed on a 300 promax was wondering how many hours per mercury does the job require. Also how reliable are these engines? Any imput greatly appreciated. Thank you Bryan
  4. B

    Verado 200 4 cylinder

    Hello, Warning Vent SW Hi displays on vessel view but system states OK, How can I clear the code after having FSM repaired was told there was a schrader valve to push because may have fuel in line. When vent tube was filling with fuel and filling cylinder 4 with fuel.
  5. B

    2006 Verado 150 4 cylinder

    Hello, My 2006 verado 150 fills #4 cylinder with fuel, injectors cleaned this week. No issues remove plugs and fuel qpours out of cylinder #4 even with injector rail removed from intake. Crank engine over and sprays it out. Turn by hand and use flash light you can see the fuel raise in the plug...
  6. B

    Verado no crank at key

    Hello Just purchased a 200 verado theft recovery have replaced the PCM as it was shorted out when harness cut. Engine starts and runs when jumped at the starter. Have tried other PCM and same issue, have also replaced the key switch. Just wondering if this has to be set up as the binnacle needs...
  7. B

    150 Verado lower cowling

    Hello All, looking for for a lower pan (cowling) for 2006 150-200 verado. It is the part that the cowling attaches to before the chaps(midsection covers) I need the port side but may purchase the complete lower cowling. Thank you
  8. B

    Mercury Verado PCM

    Hello Does the PCM have to be programmed to the serial number on the engine. Thank you, Bryan
  9. B

    Black foam in coolant

    Hello all, I have had lots of issues with these Tamd40b and the Ms3c gear cases, now a new problem with the engine one of them has black like foam in the coolant tank. It floats on top of the coolant, I have recently cleaned the heat exchangers rebuilt the coolant pumps and refilled with...
  10. B

    1999 Mercury 150 EFI idles rough

    Hello all My 1999 Mercury 150 EFI idles rough it smooths out above 2000 rpm. I replace plugs and low pressure fuel pump. I have checked the fuel pressure regulator and has 36psi key on engine off as described per manual. It runs as if something out of balance when in gear also at 1500-2000 rpm...
  11. B

    1999 mercury 150 EFI saltwater series runs rough at idle

    Hello all I have a 150 EFI 1999 model that runs rough at idle, I have checked compression and they are all at 120 psi I have also installed new plugs, Also I was wondering what the mix of oil is because it is on a 19 Silver King and no room for the Oil reservoir, so that is the way it was...
  12. B

    MS3C Transmission

    Hello all I have 2 TAMD40b with the MS3C transmission and both have a delay going into gear in both directions. One has a 20 second delay or so and if you increase the RPM it will jerk into gear. Once the are in gear they are fine and no chatter, slip etc. Once shifted to Neutral same thing and...
  13. B

    Tamd 40b cold start

    Hello all, I have finally made back into the water after 6 years. One of the engines have an issues starting on cold starts everything is fine after running for 4-5 minutes and restarts all day long just fine. On the first start after warming the glow plugs for 20 sec or so it attempts to...
  14. B

    Tamd40b

    "Hello, I have a pair of tamd "Hello, I have a pair of tamd40b diesels in my topaz.The port engine has blown off the big rubber end plate with the two small hoses off several time,I have replaced the end plate which is about 4" diameter still the same problem.This is located behind the heat...
See more
Back
Top