Logo

OEM parts incorrect?

The flush fitting will test for water circulating through the block, what is will not test is if the plastic washer that sits on top of the water tube / grommet, that is sandwiched between the powerhead and mid section has beed distorted or melted from overheat that would restrict waterflow coming through the water tube into the block. The powerhead needs to be removed to validate the condition.
My response was confusing. What I meant is that I can use the flush fitting into the water tube(where it would connect to the water pump.)

Tried the water attachment to lower tube and nada.. looks like I’m removing powerhead.
 
And here it is! Totally melted the plastic washer and was completely impeding the flow to engine.

So, I know I need a new washer for top of water tube as well as a new gasket.

The hole above the clogged washer seems really small. Picked at it a little bit to see, but curious how big it should be.

Anything else to do while I’ve got powerhead off?

Definitely would prefer to not have to do it again!

Internet is down but will send photos as soon as I can
 
you can see the melted plastic washer totally clogging the input to the motor.
I sprayed some carb cleaner through the engine side of the water passage and it seems pretty clear.
 

Attachments

  • IMG_2745.jpeg
    IMG_2745.jpeg
    64.1 KB · Views: 43
  • IMG_2746.jpeg
    IMG_2746.jpeg
    56.9 KB · Views: 48
Im seeing the gasket for the powerhead to sit on #11-- 27-39050 but I'm not seeing the washer for the top of the water tube.
Also, wondering if a bad thermostat could have started the whole issue? Is there an easy way to check this?

1719421591372.png
 
OK, just realized this engine doesn't have a thermostat. Water outlet is just at the back of the cylinder block.

I found the parts for the engine locally. There is a seal and a spacer for the water tube
 
You have the wrong view, the link I sent you earlier for the bottom cowl is the correct one. Anyway, as Jeff Foxworthy one said "There's your sign"! What probably caused it is a bad impeller. The design of that pump system was garbage, Those impellers were weak at best, way too small and squished way too much, once a year replacement if you put any hours on them. I usually keep 4or 5 instock for my collection, I'v got to where I store the engines without impellers in them. If I want to run one, i spend the 20 minutes to put one in and go play.

Glad you got her fixed...
 
So, I got the whole lower unit together: new water pump, proper key, new impeller, as well as new seals for the shift shaft. I put a new seal and spacer over the water tube, and a new gasket under the powerhead. Attached water pump(with all proper parts) and torqued to specs. Did the bucket test before attaching lower unit, and pump was pumping water, though not as well as the chinese pump that I had before(Its possible the drill was spinning at less RPMS). I attached lower unit, turned engine on, and same thing! no water, only steam..Quickly turned it off.

Took off powerhead again. I thought maybe my permatex gasket sealer had leaked to cover water pump hole. It hadn't. I took compressed air, and could tell that the passageways through the powerhead were clear. I tried putting air through powerhead water exit. I felt a strong air from bottom of powerhead(that attaches to watertube) as well as from the other hole that goes to exhaust. I also checked from top of water tube and could feel powerful air coming out of lower unit where water is pulled up. It seems like everything is clear from watertube to exit of powerheard.

Impeller is solidly on key and is spinning well. All the seals are in it. I don't know what to do other than take it apart and rebuild it
 
A hole in the exhaust plate forcing exhaust gases back into the cooling passages preventing the water to circulate in the block, the other would be a breach of compression from corrosion in the cylinder cooling area typically in the blind pocket next to where the spark casting is. Very common in saltwater engines that weren't flushed properly. I've had a pile of those blocks in the past, but that condition usually shows up as water on the spark plug.
 
A hole in the exhaust plate forcing exhaust gases back into the cooling passages preventing the water to circulate in the block, the other would be a breach of compression from corrosion in the cylinder cooling area typically in the blind pocket next to where the spark casting is. Very common in saltwater engines that weren't flushed properly. I've had a pile of those blocks in the past, but that condition usually shows up as water on the spark plug.
Without knowing specifically what you are talking about(tenuous grasp on some part names) this is kind of what I’m thinking. Is this something I would be able to see? I don’t know enough about the cooling system to diagnose this.

The main channel in the exhaust plate that goes to the tell tale has 2 holes in it. When I first looked, I thought there was only one, it went straight down and seemed pretty small. I realized later that the main coolant passage went off to the right. I’ll see if I can find a picture of that. Possibly that’s not supposed to be there?

I bought the motor used, with a lot of hours on it, and to be honest have been much more vigilant with my 115hp. This one was used a decent amount with only periodic flushing in the puget sound, so very possible that there is damage from salt corrosion
 
I'm looking through the pics. The hole I am referencing is in the powerhead. This is from a pic when I first removed it.
The hole in the center going down is the one I am questioning. Is there anything specifically to look for for a leak in exhaust plate?
Any fixes if this is the issue?
IMG_2746 (1).jpeg
 
The exhaust baffle plate separates the dry hot exhaust gases exiting the cylinder ports and the cooling water circulating between the plate and exhaust cover. This cools the hot exhaust and mixes with exiting water has it heads into a tuner/adapter or just dumps into the midsection and out through the propeller hub. You can actually see the seam of the plate and cover in right of your photo. If there is a hole in that thin stainless plate, it can push hot exhaust gases back into the coolant water flow and interupt or stop water from flowing up the block and into the powerhead causing overheat. The challenge with finding this out is that the exhaust cover bolts are notoriously stuck and can break easily without heat (MAPP) gas torch and finesse and slowly working the bolts out, tighten and loosen until they unscrew, this can take hours to do, but saves a trip to the machine shop to get them drilled and re-tapped. The water cover where the spark plugs are is equally as challenging. I've lived in Florida saltwater my whole life so this stuff is second nature but I still break a screw every so often.
 
A hole in the exhaust plate forcing exhaust gases back into the cooling passages preventing the water to circulate in the block, the other would be a breach of compression from corrosion in the cylinder cooling area typically in the blind pocket next to where the spark casting is. Very common in saltwater engines that weren't flushed properly. I've had a pile of those blocks in the past, but that condition usually shows up as water on the spark plug.
The first thing I did before working on the motor was to test compression. Both cyclinders were a little over 120psi
 
The exhaust baffle plate separates the dry hot exhaust gases exiting the cylinder ports and the cooling water circulating between the plate and exhaust cover. This cools the hot exhaust and mixes with exiting water has it heads into a tuner/adapter or just dumps into the midsection and out through the propeller hub. You can actually see the seam of the plate and cover in right of your photo. If there is a hole in that thin stainless plate, it can push hot exhaust gases back into the coolant water flow and interupt or stop water from flowing up the block and into the powerhead causing overheat. The challenge with finding this out is that the exhaust cover bolts are notoriously stuck and can break easily without heat (MAPP) gas torch and finesse and slowly working the bolts out, tighten and loosen until they unscrew, this can take hours to do, but saves a trip to the machine shop to get them drilled and re-tapped. The water cover where the spark plugs are is equally as challenging. I've lived in Florida saltwater my whole life so this stuff is second nature but I still break a screw every so often.
So, it sounds like this is the next step. I'm assuming I should removed the powerhead to do this. I'm gonna look at the waterpump one more time to make sure there isn't something there.

Any tips on what you do with the torch and bolts? Ive avoided this to this point for this exact reason.
 
So, it sounds like this is the next step. I'm assuming I should removed the powerhead to do this. I'm gonna look at the waterpump one more time to make sure there isn't something there.

Any tips on what you do with the torch and bolts? Ive avoided this to this point for this exact reason.
And, just to confirm, I'd be removing this.?
 

Attachments

  • IMG_2748.jpeg
    IMG_2748.jpeg
    57.4 KB · Views: 44
Before you take the plate off, are you able to get water through using the flush attachment to the watertube and see water coming up through the water tube with the powerhead removed? looking for a piece of impeller vane lodged in the watertube.
 
Well, glory be! I'm glad I checked the
Before you take the plate off, are you able to get water through using the flush attachment to the watertube and see water coming up through the water tube with the powerhead removed? looking for a piece of impeller vane lodged in the watertube.
Yes. It seems that every channel is pretty clear. I checked everything also with compressed air, and there was quite a bit of pressure coming out of the ports.
 
Are the grommets in place in the water pump housing where the water tube fits nice and snug? Are the grommets in place between the intake grid under the cavitation plate, the cross over pipe and the grommet going into the pump base nice and snug? Just trying eliminate low hanging fruit.
 
Well!!! Lookee here!

I've got water! I don't know what happened last time I put the whole thing together and checked it, but i went through the pump one more time. I used the chinese water pump top because it doesn't have a hole under the water tube pickup(probably not a big deal, but with all the issues I have been having with parts..)

The water coming out is pretty hot. I can't keep my fingers in it. There is quite a bit of exhaust and smoke. You can see with the second attached movie. This is how the motor was performing when I bought it. Maybe it is running too hot and that is what melted the washer initially? I do know the replacement washing is supposed to be quite a bit sturdier.

Wondering if even though im getting good water flow, that exhaust is still leaking?

IMG_2753.jpeg
IMG_2754.jpeg
 
Are the grommets in place in the water pump housing where the water tube fits nice and snug? Are the grommets in place between the intake grid under the cavitation plate, the cross over pipe and the grommet going into the pump base nice and snug? Just trying eliminate low hanging fruit.
you mean those seals that have the round lip to hold them? If so, yes. Both of the seals are there.

Curious to hear your thoughts now that I have water coming through
 
Can you hold your hand on the exhaust plate while the engine is running? You should be able to without discomfort
I did briefly when checking earlier and it didn’t seem super hot. I’ll check again when I’m back from a meeting.

The only motor I have to compare it to is my 88 115 and that motor runs much cooler. I also don’t have near as much exhaust smoke
 
Hook up the pee tube back to where it needs to be, that resrtiction is an engineered discharge diameter that helps the cooling water pull more heat away by slowing down the water flow through the block. If you can hold your hand on the exhaust plate and the aluminum welsh plug on the starboard side of the block without it burning you, you should be good to go. If you have a laser temp gun, you should be around 100-110F at diffrent points around the block.
 
Back
Top