Logo
FULL SITE MENU

Recent content by 9nick0

  1. 9

    Suzuki 115 DF water cooling problem

    I did, we blew out all lines and tried weed cord. And the Tupperware container was over the intakes a few inches.
  2. 9

    Suzuki 115 DF water cooling problem

    Hi, I recently took my 2018 Suzuki 115 out and it wasn’t peeing when it had been previously. I was able to idle back to the dock which was about a 30 minute trip and it never overheated. I took it home and put a new impeller kit with gaskets, etc… in it. I put it on the ear muffs and she wasn’t...
  3. 9

    1955 Old Boat Motor 15hp runs but I need help

    I have a 1955 15hp evinrude painted in blue. It runs but there is a fuel issue going on. It appears it has been modified to run with a non-pressurized fuel tank and I wanted to see if anybody might have experience in that.
  4. 9

    Mercury 175-200 4 stroke Needed

    I am looking for a 175-200 Mercury 4 stroke. Willing to pay to have it shipped. Just needs to check out compression wise and be in strong running condition. I don't believe I need the controls.
  5. 9

    Grease fitting for MD40B Motor travel position

    There is a lever on each side to lock this motor in the up position for travel. Mine are rusted pretty good and need to be knocked free to be used. I was told there is a potential grease fitting for this and I wanted to see if anybody is aware of where it might be. I have wd-40 and blastered it...
  6. 9

    Oil and spark plugs

    I have the MD40B Tohatsu 40 horse 2003 tldi and I am wondering what kind of oil will be required to run through the motor. I have a few unopened jugs of Evinrude premium oil still from a previous motor are those ok or is a specific brand and mix recommended for these? Also, are the $15 a spark...
  7. 9

    1000 cranking amps

    I have a 2003 MD40B 40 horse TLDI that requires the 1000 cranking amps. I just realized all of this and that my battery is significantly underpowered. It’s an old 575. The motor is now throwing the 3 blinking red lights and idling a little rough on start so I am coming to the conclusion I need...
  8. 9

    Help Please

    I have a 2003 Tohatsu MD40B and when the battery is hooked up I can’t get the tilt and trim to work at all. Worked fine until I tried to switch batteries when it was running on low voltage. I have checked the fuse panel under the console and just went ahead and replaced them. Is there another...
  9. 9

    2003 MD40B Tohatsu 40hp New Problem

    New problem now, got everything else figured out and she ran great one time. Tried to put her in a second time and she just clicks. I tried 3 different batteries and the power tilt and trim isn’t working either. Any suggestions?
  10. 9

    2003 40hp Electric Start Low DI Questions

    I purchased a Carolina Skiff with a nice sounding 2003 Tohatsu. It looks like an extremely low hour motor. What kind of compression results should I expect to see as acceptable? Anything else that can be shared about this motor if anybody is aware of anything.
  11. 9

    2003 40 hp 2 stroke impeller help

    I just bought a 2003 40 hp two stroke, impeller needs to be replaced is this a job that I can do or a job for a service department and if so what should I expect to pay?
  12. 9

    2006 Mercury 4 Stroke 9.9 hp oil pump

    I bought this motor to attempt to fix it up it’s a 2006 Mercury 9.9 with what appears to be a locked up oil pump. What can I do to test to see if this is indeed the problem or are there any other tests that can be done to see if additional damage?
  13. 9

    1955 Evinrude 15hp

    I have a 1955 Evinrude 15/18 hp. I just cleaned the carb and it appears the motor is not getting proper fuel. I am replacing the fuel lines but could this be anything else? Also, the fuel connector on mine has a single male part whereas I have seen some pictures of them with 2. I also have what...
  14. 9

    5 hp 1990 Nissan 2 Stroke Low Compression Runs Good

    I bought a 1990 Nissan motor in actually really good condition except for the compression numbers are barely getting to 60. It starts up fine, runs wide open fine but won’t idle or slow down enough for a smooth shift. Any recommendations? Running some seafoam through now as well as some carb...
  15. 9

    2017 4 HP Tohatsu 4 Stroke 10psi Compression

    I bought this motor without properly checking it out. The guy I bought it from was able to start it some how but when I got it home and put the gauge on it it reads as 10psi on compression. Pulls way too easily. I can’t sell it and Ofcourse this guy has disappeared so what do I look at first? I...
See more
Back
Top