Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
ENGINE ACCESSORIES
Model
Model Notes
Year Range
Serial # Range
Oil Drain Hose Kit with Tether
MCM V-8 (496cid)
12MM oil plug threads
2009 - 2013
1A349411 and up
MCM V-8 (502cid)
1/2-20 oil plug threads
1990 - 1993
0C878221 - 0F802599
MCM V-8 (502cid)
12MM oil plug threads
1996 - 2001
0F802600 - 0M024999
(1) Kit not available
FUEL FILTER
WATER ELIMINATOR
Uses polymer crystals encased in a plastic filter to absorb water from
the fuel in a fuel tank. Supplied with a 2 ft.(610 mm) lanyard. Sold in
counter display box. Approximate dimensions: 3‑1/2 in.(89 mm) a 1‑1/4
in.(32 mm).
WATER ELIMINATOR
Replacement in‑line filter
Fits all MCM/MIE gasoline engines using a boost pump.
WATER SEPARATING FUEL FILTERS -GASOLINE
WATER SEPARATING FUEL FILTER KIT
Contains a drying agent commonly used to keep small, sealed containers dry. It
absorbs water that has collected in the fuel tank.
How to use: Attach to the inside fuel cap with the lanyard (included). Adjust the
lanyard so the Water Eliminator sits at the bottom of the fuel tank. Replace as
needed.
For use in all octane grades of gasoline, including ethanol blended. Not
recommended for diesel fuel.
For use in all 2‑cycle and 4‑cycle gasoline outboard, sterndrive, inboard and jet
drive marine engines.
Priced individually, sold @ multiples of 6
Quicksilver Branded, Point of Sale Packaged.
FUEL FILTER KIT
FUEL FILTER KIT
For gasoline use only. Degree of filtration is 25 micron, minimum.
Used in both outboard and MerCruiser applications (except 1992 MerCruiser 4.3 L
Gen II engines equipped with an in‑line fuel filter).
Quicksilver Branded, Box Point of Sale Packaged.
WATER SEPARATING FUEL FILTER KIT
Prevents blockage of the boost pump inlet from debris that may be in the fuel tank.
This filter is installed in‑line between the fuel tank and boost pump. Standard
equipment with all current engines using a boost pump. This filter will backfit older
MerCruiser 8.1S/496 Mag engines.
Fits all MCM/MIE gasoline engines using a boost pump.
For gasoline use only.
For use on 1992 MCM 4.3L Gen II engines equipped with an in‑line fuel filter.
1218