Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
COOLING SYSTEM
HOSE - MOLDED
HOSE - MOLDED
Transom to oil cooler
Cooler to thermostat housing
1‑1/4 in. (32 mm) I.D. at one end; 3/4 in. (19 mm) I.D. at other end of hose
1‑1/4 in. (32 mm) I.D. at one end; 1 in. (25 mm) I.D. at other end of hose
Fits MCM 3.0L, GM V‑6 & V‑8 (305 & 350 cid) engines
Fits 3.0L
HOSE - MOLDED
HOSE - MOLDED
Thermostat housing to exhaust manifold
1 in. (25 mm) I.D.
Fits GM in‑line 4 & 6 cyl.
HOSE - MOLDED
Transom to oil cooler
1 in. (25 mm) I.D. at one end; 3/4 in. (19 mm) I.D. at other end of hose
Fits 3.0L/LX
HOSE - MOLDED
Thermostat housing to exhaust manifold
1 in. (25 mm) I.D.
Fits GM in‑line 4 & 6 cyl.
HOSE - MOLDED
Cooler to thermostat housing
1 in. (25 mm) I.D. at one end; 3/4 in. (19 mm) I.D. at other end of hose
Fits 3.0L/LX
HOSE - MOLDED
Thermostat housing exhaust manifold
1 in. (25 mm) I.D.
Fits 3.0L/LX
Cooler to thermostat housing
1 in. (25 mm) I.D. at one end; 3/4 in. (19 mm) I.D. at other end of hose
Fits 3.0L/LX
868