Logo
FULL SITE MENU

Search results

  1. B

    What does omc or bmc stand for

    I am new at the boat thing an I am new at the boat thing and i am unsure what spark plug to use. The table says if it is a omc or bmc to use a spark plug number QL77JC4 and all others to use a L77JC4 for a 91 johnson-evinrude. How do I tell what it is.
  2. B

    1979 evinrude 140

    Hi guys just picked up a 1979 Hi guys just picked up a 1979 140 evinrude outboard for 300 dollars tilt trim the works from a guy i work with it was on his ski boat he said it needed total rebuild but it runs and the compression on all cyclynders is 100 he belives I will find out this weekend...
  3. B

    Prop

    What is the recommended prop What is the recommended prop for an AQ125A? General use - some skiing - mostly just running to fish.
  4. B

    Marine vs Automotive Fuel Pump

    " I had a 350 long block insta " I had a 350 long block installed a couple of years ago in my boat (inboard/outboard). At the time, the mechanic also installed a fuel pump. I believe at the time the mechanic told me that there was really no difference between the two pumps. Is this true? I'm...
  5. B

    Overheating 2001 50 hp 4 stroke yahama low hours

    how hard to change thermostat how hard to change thermostat or waterpump
  6. B

    1994 lower unit Yamaha 150

    Hi just a ? What could be som Hi just a ? What could be some of the problems why I have water mixing in with my oil in my lower unit.I was hoping to get some ideas before I start looking at it.I did buy the yammaha chilton book but it doesnt show much for the 150's in it.Any suggestions would...
  7. B

    Question for Tony

    " Have a 2001, 75 HP Mercury f " Have a 2001, 75 HP Mercury four-stroke. Problematic starting when cold even though it is summertime. Seems to be set at very low idle speed. Would this affect the starting ? When it's warmed up, it starts fine. Any suggestions to improve the cold starting ...
  8. B

    Please help

    When sealing a crankcase with When sealing a crankcase with the spaghetti seal should i use the Gel Seal too?
  9. B

    Question for Joe

    " Hello, I have a Evinrude 90h " Hello, I have a Evinrude 90hp with model# E90TLCIH and the serial# J0001524. I would like to know the year of this motor and if the powerhead is the same as a 1976 85hp evinrude? i need to change a piston in the 90 and i have the 85 with a really good piston...
  10. B

    What year is this outboard

    i have a 60 HP chrysler but i i have a 60 HP chrysler but i don't know the year of it the serial #2097 and the model #60911A can anybody tell me anything about this motor and maybe what control box goes with it there was not one when i got it thanks
  11. B

    Old Evinrude need info

    " I picked up a old Evinrude a " I picked up a old Evinrude and need some information for it.It looks to be a 3Hp or 2HP.The serial # is 3022-09735. Can anyone tell me the year,HP,and what spark plugs to use? IT is a two cyl.model.Also I see it takes 8oz. of oil per gal. of gas (sae 30 )I had...
  12. B

    Mercury 199290hp 3 cylinder two stroke seized steering

    The rod that the steering lin The rod that the steering link rod and steering cable attaches to appears to be seized inside the steering cable tube. I have tried applying heat and force to no avail. Any suggestions? Bill
  13. B

    Need a new tach what should I get

    This is on a 1972 85hp Johnso This is on a 1972 85hp Johnson. My tach must have shorted out the face plate smoked up and it quit. Can I pick up a two wire tach at a auto parts store? Thanks for any feed back
  14. B

    Hydrofoil

    I have 85hp on a 15ft v botto I have 85hp on a 15ft v bottom it had a hydrofoil on it. with it on the boat wants to lean to witch side has the most weight mostly the left. And turning sharp can be a little scary. Is there any other types of foils out there that wouldn't do this. I like having...
  15. B

    1960 Evinrude 3 hp pump amp needle valves

    " 1). I tried to remove my " 1). I tried to remove my lower unit (four bolts) to get access to check the impeller. While the outer components separate easily, I could not get the lower unit off the drive shaft, and didn't want to force things. Should it have come off or is there something I...
  16. B

    1960 Evinrude 3 hp pump amp needle valves

    " 1). I tried to remove my " 1). I tried to remove my lower unit (four bolts) to get access to check the impeller. While the outer components separate easily, I could not get the lower unit off the drive shaft, and didn't want to force things. Should it have come off or is there something I...
  17. B

    Gasoil mix for 1982 Johnson 70 hpoutboard

    " I have a 70 hp Johnson outbo " I have a 70 hp Johnson outboard. It has a 6 gallon gas tank. What is the proper amount of oil to add to the tank when I fill it? Also, do you add the gas or the oil first. Thanks, Bill. "
  18. B

    b81 Johnson 70 hp restarting

    "I am new to power boats & "I am new to power boats & i recently purchased a used boat with a '81 Johnson 70 hp 3 cylinder engine. The controls have a bar to lift up all the way to where it says "High idle/start". Also it says to push the key in when starting to choke. The engine starts...
  19. B

    Goodyear C B 5 outboard info needed

    We have a goodyear c b 5 hors We have a goodyear c b 5 horse outboard motor and cannot find any information on it at all. Could please assist if you know anything about it. We would like to know how old it is and what it is worth. Thank you...
  20. B

    Yanmar industrial to marine model TK353

    " Hello, This is an industr " Hello, This is an industrial engine I'm going to convert to a marine engine. It was made for Thermo King by Yanmar. Thermo King is a company which transports refrigerated goods across country. Does anyone have any information on these? Parts, manuals, info...
Back
Top