Logo
FULL SITE MENU

Search results

  1. T

    AQ140/280 PDS bearing(s) question

    I am finding some time to work on the AQ140/280 that I have posted questions about earlier this summer. I pulled the PDS and the bearing. There is another small roller bearing in the flywheel cover cavity past the forward seal and forward of the B/W splines. This bearing appears to be in good...
  2. T

    AQ140/280 Transmission and drive shaft issues

    I took the boat with the 1978 AQ140/280 out today to trouble shoot overheating issues. After running at planing speed for about ten minutes I noticed that the upper drive housing (transmission) was quite hot to the touch. The gears, bearings, or something in the housing are also faintly rattling...
  3. T

    AQ140A running hot? Advice needed

    Greetings. I have recently aquired a 1978 Chrysler Sport Fury with an AQ140A engine on a 280 outdrive. The boat has two temperature gauges. One is on the dash and does not have numbers, only C---H. The other is mounted under the port rear seat facing forward and has numbers. The sender for the...
  4. T

    1974 70 HP Johnson water pump/cooling question

    I have acquired a boat with a 1974 Johnson 70 HP model 70ESL74M. When I run the motor there is water coming out of three small holes on both sides and the back of the lower unit near the water pump intake, but none out of the exhaust port like on my 1966 Evinrude. At idle the heads are hot, you...
  5. T

    Gearcase lube question

    What is the difference between the Type C gearcase lube and the 80W-90 hi-vis lube? I have two motors and one calls for Type C and the other hi-vis.
  6. T

    Fixing Evinrude 1982 140hp- Lots of Questions

    Greetings, I am trying to fix up a 1982 140 HP Evinrude that has sat for seven years and I am running into problems. I went through the lower unit yesterday. I also cleaned the carbs and the fuel filter. The engine starts and idles OK and water flow looks OK. Problem 1: The top right...
  7. T

    1982 Evinrude 140hp water pipe grommet

    Greetings, I acquired a 1982 Evinrude 140 hp v4 on the cheap. I pulled the lower unit and there is no water pipe grommet between the water pump outlet and the uptake pipe. My 35 hp has one so I am wondering if this engine is missing its grommet or if it does not need one. Also, any tips for...
  8. T

    Question About Fuel Consumption

    I have a 1965 33 HP Evinrude S I have a 1965 33 HP Evinrude Ski Twin on a 14 foot aluminum boat. On Sunday I spent about two hours pulling the kids on a tube and used about four gallons of gas. Is this a lot or normal? It seems like a lot to me. If it is too much then what is the cause...
  9. T

    1965 Evinrude Motor bBumpb Problem

    "Greetings. I have a 1965 Evin "Greetings. I have a 1965 Evinrude 33 HP that has developed a 'bump' that started occurring intermittently today. Eventually it progressed to ‘bumping’ every three to five seconds. The ‘bump’ occurs when the motor is in forward or reverse. It is similar to hitting...
  10. T

    1965 Evinrude Sparkplug and Part Info Needed

    "I received my manuals but I s "I received my manuals but I still need some help. This is for a 1965 Evinrude 33 HP model 33552. I need to find OMC part number 307290 "Hook, Cover to housing". I also need to know what sparkplugs are recommended and if they should still be gapped to .030 as the...
  11. T

    Evinrude Part Info Needed Again

    My parts manuaul is on the way My parts manuaul is on the way but I can't wait for this. I need a throttle cable and the small metal plate that attaches the back of the engine cowling to the upper unit for a 1965 Evinrude 33 HP model 33552. This is on a 14 foot Gregor. The throttle is...
  12. T

    Water Pump Part Info Needed

    Greetings. I have a 1965 Evinr Greetings. I have a 1965 Evinrude 33552. The engine overheated and I pulled the lower unit to check the impeller. The impeller is getting replaced but the problem was in a small rubber gasket that fits inside the top of the impeller housing water outlet and...
Back
Top