Logo
FULL SITE MENU

Recent content by nicknack2

  1. N

    lower unit pushing/coming out/raising out of the water when put on revers and given throttle.

    Hey guys my 1998 200hp Johnson is coming out of the water(lower unit raising up), not holding the the trim down position when transmission is on reverse and given throttle. any ideas what might be causing the issue? the motor holds the trim position when given throttle in forward gear, but not...
  2. N

    trim/tilt limit switch

    Good morning, does any one know/have a picture of where the tilt/trim limit switch connects to? I was working on my motor, got it disconnected and now I don't know where it goes to.
  3. N

    1998 200HP Johnson Reed valves

    Good morning, my motor kept dying at idle in the water, started troubleshooting it and it is spitting a little bit of fuel out of the port's side 2nd/middle carb. My question is, if I replace those reeds, should I replace all the reeds on the engine as well? is that the norm when it comes to...
  4. N

    1998 200 Johnson hard to start

    Hi guys, I have a 1998 200 Jonhson which I have trouble starting after it seats for a day or two. I pump the bulb until is hard and then crank, it takes more than 4 or 5 tries to start, I take it easy on continued cranking (10-15 seconds at the time) to avoid draining the battery or burning the...
  5. N

    1998 200hp Johnson gear shifting problem 25” leg

    Good afternoon all, after resealing my lower unit and putting it back together I’m having issues getting the motor to go in to forward gear, I can set the controller to forward and then go to the back of the motor and push the rod up slightly and the motor will engage the forward gear. Anyone...
  6. N

    1998 Johnson (200 HP) shifting issues

    Good Morning All, after replacing the impeller and resealing my lower unit I’m having trouble getting the motor in to gear, I understand the shift rod height has to do with this issue as before I took the unit apart I did not the problem, by the book it states to screw the rod in to the shifter...
  7. N

    Steering

    Posted this in a different forum with little luck, since this is for my Evinrude I'm going to give this a shot here... "Hey guys I ordered a new steering cable (M66)16 footer for my boat, but it doesn’t come with the nuts on both ends to hook up to the hem and the steering tube where it...
  8. N

    New steering cable

    Hey guys I ordered a new steering cable (M66)16 footer for my boat, but it doesn’t come with the nuts on both ends to hook up to the hem and the steering tube where it connects to the motor, do I need to order another type of cable or is there an adapter(I guess two adapters) to make this work?
  9. N

    Shifter rod O-ring(s)

    All, I have a 1998 200 Johnson which I’m re-sealing the lower Unit, I made the mistake of trying to replace the two o-rings that go in the rod/shifter cover plate... everything went fine until I tried to insert the second ring there is no way I can get that done... as I could not get the second...
  10. N

    johnson 200 HP oil /water

    this is the situation... when I run(during cleaning) my 1998 200 HP Johnson on the ears muffs I get al oil/water mix off the lower unit/propeller hub...so I was thinking I had a prop shaft seal problem...so I took the boat out to a spot I know where we snorkel and just have fun in the water...
  11. N

    Clams Canino

    Any one knows the Phone number for Mr. Canino, I lot his business card...I'm looking for a stator(merc 115) but can't figure out model number in order to order it, I'm thinking of sending it to him, I'm sure he'll figure it out and probably has a used one laying around some where.
  12. N

    1998 200HP lower unit seals and O-ring...

    how can I tell the difference between leaking seals or a leaking O-ring on the lower unit of my motor???
  13. N

    year, HP and model of this mercury???

    This is the serial number of this motor I believe it is a 115 HP C300734
  14. N

    shifting...

    guys my motor(1991 200 hp Johnson) is not shutting down half of the engine when you shifting in to forward or reverse, the switch is good, I can press it and shuts off half of the motor, how do I adjust the switch???
  15. N

    wire color

    Guys I'm installing a stereo and I'm trying to figure out what color is the accesory wire coming from the ignition switch on my 200 HP Evenrude, so I can hook up my red wire in to it, so my stereo runs only with my switch on... any one knows??
See more
Back
Top