CDI Electronics Outboard Ignition Troubleshooting Guide

66 TROUBLESHOOTING GUIDE - Johnson/Evinrude Troubleshooting Johnson/Evinrude Troubleshooting 3. Replace the ignition coil on the cylinder dropping spark. ENGINE WILL NOT SHUT OFF: Disconnect the stop wires at the power pack. Connect a jumper wire to the stop wires from the pack and short it to engine ground. If this stops the pack from sparking, the stop circuit has a fault. Check the key switch, harness and shift switch. If this does not stop the pack from sparking, replace the power pack. Repeat test as necessary for additional packs. MISS AT ANY RPM: 1. Disconnect the Yellow wires from the stator to the rectifier and retest. If the miss clears, replace the rectifier. 2. In the water or on a Dynameters, check the DVA output on the Orange wires from the power pack while connected to the ignition coils. You should have a reading of at least 150V DVA or more, increasing with engine RPM until it reaches 300-400V DVA maximum. A sharp drop in DVA right before the miss becomes apparent on all cylinders will normally be caused by a bad stator. A sharp drop in DVA on less than all cylinders will normally be the power pack or timer base. 3. Connect an inductive tachometer to each cylinder in turn and try to isolate the problem. A high variance in RPM on one cylinder usually indicates a problem in the power pack or ignition coil. Occasionally a timer base will cause this same problem. Check the timer base DVA voltage (see NO SPARK ON ANY CYLINDER above). 4. Perform a high-speed shutdown and read the spark plugs. Check for water. A crack in the block can cause a miss at high speed when the water pressure gets high, but a normal shutdown will mask the problem. 5. Check the triggering and charge coil flywheel magnets for cracked, broken and loose magnets. ENGINE WILL NOT ACCELERATE BEYOND 2500 RPM (Runs smooth below that RPM): 1. Use a temperature probe and verify that the engine is not overheating. 2. Disconnect the tan temperature wire from the pack and retest. If the engine now performs properly, test and replace the defective temperature switch, VRO, engine harness or boat harness. 3. Make sure the tan temperature switch wire is not located next to a spark plug wire. 4. Disconnect the VRO sensor from the engine harness and retest. If the engine performs correctly, replace the VRO or sensor. ENGINE STAYS IN QUICK-START: 1. With the engine idling, check the Yellow/Red wire for DC voltage. If there is DC voltage on this wire while the engine is running, the Quick-Start will not disengage. A voltage of less than 7 volts will not engage the starter solenoid, yet will engage Quick-Start. 2. Short the White/Black temperature switch wire FROM the power pack to engine ground. Start the engine, if the Quick-Start drops out after approximately 5 seconds, replace the White/Black temperature switch. 3. Disconnect the Black/White wire from the power pack. If the Quick-Start feature is not now working, replace the power pack. ENGINE DIES WHEN QUICK-START DROPS OUT: Check ignition timing at idle with the White/Black temperature wire disconnected. Remember to allow for the drop in ignition timing when Quick-Start disengages. Verify ignition timing after engine has warmed up, according to the service manual. ENGINE WILL NOT ENGAGE QUICK-START: 1. Disconnect the White/Black wire from the temperature sensor. 2. With the engine idling, check the Black/White timer base wire for DC voltage. There should be about 6 to 10 volts DC voltage on this wire while the engine is running for the Quick-Start to engage. 3. Short the White/Black temperature switch wire FROM the power pack to engine ground. If the voltage on the Black/White wire drops out after approximately 5 seconds but the engine timing does not change, replace the timer base. If the voltage remains present, disconnect the Yellow/Red wire to the pack and repeat the test. If the voltage still remains, replace the pack. ENGINE TIMING TOO HIGH: 1. Check the flywheel center hub magnet to make sure it’s tight. Look for signs of cracks and bulges in the Brown ferrite magnet material.