Logo
FULL SITE MENU

Search results

  1. C

    2000 0X66 200HP hi pressure fuel spec

    Red wire on TPS is power supply will be max 5.3 volts measured to ground for future refference
  2. C

    2000 0X66 200HP hi pressure fuel spec

    Found the problem broke wire in harness from the TPS boat runs wot 6300 rpm over 60 mph thanks for all advise much appreciated .
  3. C

    2000 0X66 200HP hi pressure fuel spec

    I would think it would increase as the TPS changes, 0 volts on TPS at idle and wot.
  4. C

    2000 0X66 200HP hi pressure fuel spec

    Fuel pressure is 30 psi
  5. C

    2000 0X66 200HP hi pressure fuel spec

    Timing checked out good O2 sensor had a lot of carbon build up I took it all apart and cleaned the housing that it screws into replaced O2 sensor still have the same problem no power RPm will not go over 1500. I checked TPS has 0 volts showing at idle and WOT I ordered a new one but want to make...
  6. C

    2000 0X66 200HP hi pressure fuel spec

    Thanks I am only getting 30 PSI and idle while in gear is ruff almost feels like its running retarded will not plane going to check where fly wheel is at with #1 at TDC
  7. C

    2000 0X66 200HP hi pressure fuel spec

    Looking for the hi pressure fuel spec idle and 2000+ RPM suspect pump is on its way out just want to confirm, thank you in advance.
  8. C

    1999 Magnum EFI no start

    I ordered switch pack realized I’m getting signal from pick coils on fly wheel
  9. C

    1999 Magnum EFI no start

    After further trouble shooting found starboard side no spark on those three cylinders, Port side has spark read thru some other posts and switched the red n blue wires with the red / white and blue / white on switch boxes only port side continues to have spark any help would be appreciated.
  10. C

    1999 Magnum EFI no start

    Yes its the toggle switch, ok thanks will investigate the RPM gauge i have one I can temp wire up to see if guage or something else. Thanks!!!!
  11. C

    1999 Magnum EFI no start

    824003A0
  12. C

    1999 Magnum EFI no start

    Thanks Fatz fuel pressure is in range next step is to disassemble the FMS and test for signal to injectors, located in Acworth, GA
  13. C

    1999 Magnum EFI no start

    Yes if i add fuel in the butterflies it will fire, the fuel pressure is at 36 psi key on, the RPM gauge doesnt move suspect it is bad the lanyard is in the run position.
  14. C

    1999 Magnum EFI no start

    Working on a 1999 Magnum 200 EFI cranks but will not start has spark looking to see if anyone can provide what the fuel pressure should be for the injectors also how can I test to make sure the ECU is sending the signal to operate the injectors? Thanks in advance T.
  15. C

    Evenrude piston bore spec

    Thanks racerone!!!
  16. C

    Evenrude piston bore spec

    E60TLCCR does anyone have a looking for diameter piston stock specification need to see if machine shop has enough to bore it out appreciate any help.
  17. C

    48SPL runs on water hose all dies on the lake

    Thanks Racerone should have checked compression from the start #1- 85, #2 - 155
  18. C

    48SPL runs on water hose all dies on the lake

    Yes sorry VE48ESLCCC, reeds were checked when carbs were removed and cleaned the high speed jets are the original ones to this motor which never had a problem previously I will check the compression and post it. Can you provide the flywheel torque?
  19. C

    48SPL runs on water hose all dies on the lake

    Hello new to the forum appreciate any help engine runs a little rough at idle on the trailer with the water hose connected will rev with no problems and runs smother at hi RPM, once on the lake it will get up on plane and run for about 5 min then dies no sputtering just dies what has been done /...
Back
Top