Logo
FULL SITE MENU

Search results

  1. D

    DF15A Pinion Gear Replacement - help pls!

    Hello - i sheared off some of the teeth of my pinion gear and need to replace it. I think I need to remove the drive shaft to replace the pinion gear, yes? If so, can someone point me to instructions on how to remove the drive shaft? I've removed the impeller and impeller housing but there...
  2. D

    Chrysler 360 Losing coolant and puffing white smoke

    Hey folks. I have twin 360's in my Egg Harbor. Starboard is fine but port side wont get over 2600RPM. On this port side, I'm losing coolant and puffing white smoke. The engine starts fine all the time and gets me where I'm going but again, has way less power than the other motor. Could this...
  3. D

    Distributor with 2 different springs in distributor - 1976 Chrysler 360

    not able to get over 3k RPM. reliable otherwise. opened distributor and noticed 2 different flyweight springs. one is much thicker/heavier than the other. Would the previous owner have done that intentionally? See attached.
  4. D

    Chrysler 360 losing RPM above 3k

    Went for a cruise the other day and all was well for 20min at 3k+ until I started losing RPMs on my port engine and tach started bouncing a bit. Went back to the dock slow. Started up again and revved the port engine. Idles fine but when revved to 4k it doest hold. See youtube video here of...
  5. D

    Jumping solenoid to start

    On my Chrysler 360, which lugs/contacts on the solenoid do I "jump" to start the engine without the key? I want to bump the motor over a bit to repaint the timing indicator arrow.
  6. D

    Blow by and ring replacement

    I have a ton of blow by from my 360 puffing out the dipstick tube. motor has approx 1500 hours on it but seems to run ok. question is, can i replace the piston rings without removing the crank or pulling the motor?
  7. D

    Failing Coil Problems? stalling when warmed up

    I have stalling isses on my starbord side 360. it seems to happen only when warmed up and after running a bit. I've stalled out at the dock, after backing down near idle speed when coming into a no wake zone etc. yesterday, after 5-10mins of runnign at 3k RPM, the starboard gave up 500RPMs...
  8. D

    360 - Voltage regulator shot?

    on my starboard engine, i notice that my volts increase with more rpms...the faster i rev the motor, the more volts my gauge shows. it goes from 10-14vols on the low/high side. the port motor remains stable at around 12 volts regardless of how fast my motor is revving. is this a bad voltage...
  9. D

    Flame arrestor parts needed

    anyone know where i can buy a anyone know where i can buy a replacement metal mesh part to my flame arrestor? Mine is all mashed up. It's a rochester 4bbl. I dont need a whole new unit...especially not for $100. talk about a rip-off part.
  10. D

    Volatage difference on motors

    "starboard motor volt meter fl "starboard motor volt meter fluctuates depending on RPMs (higher RPMs, higher volts). Port motor just stays are one voltage the entire time. Any thoughts? Dan"
  11. D

    360 trans fluid location

    "i've done everything to m "i've done everything to my 360s but have not touched my transmissions in a loooong time (Borg Warners). Can someone tell me where to check and fill with fluid? Thanks, Dan"
  12. D

    Engine Hours

    "now that i have a new 360 in "now that i have a new 360 in my boat, is there a way to reset the original datcon hour meter or do I have to buy a new one? there's no reset button and i'm sure that's on purpose but just wondering if there's a trick someone knows."
  13. D

    One engine runner hotten than other

    "have one new 360 (10hrs&# "have one new 360 (10hrs) and one old 360 (1500 hrs) in my 33' egg harbor. the new one is pegged to 160 degrees when running at 3200. the other runs about 20degrees hotter than that when running. At idle, it's almost the same. I'm wondering if old exhaust manifolds...
  14. D

    Replacing Cam Shaft

    "My Chry 360 was backfiring an "My Chry 360 was backfiring and disabling cylinder #7 stopped the backfiring. Was told by mechanic that it was prob due to bad cam shaft. The plug in that cylinder was wet. If it is the camshaft, is it difficult to replace? just curious to know whats...
  15. D

    KnockingClacking Heard in Carbeurator Under Load

    I have a knocking/clacking sou I have a knocking/clacking sound heard under the flame arrestor / carb that happens around 2k RPM+ while under load (in gear). It barely happens in neutral from 1500-3200rpm. I changed all the plugs and still the same problem. Please help!
  16. D

    Short vs Long Oil Filter for Chry 360

    needed a replacement oil filte needed a replacement oil filter for a chry 360 but all I could find last weekend was a short fram filter. it fits fine but it's about half the length of the regular sierra 7875's or napa 1515's. same diameter though. Any problems with keeping this fram in...
  17. D

    Chrysler 360 Exhaust Manifold Part question

    "On my starboard engine, I not "On my starboard engine, I noticed a drip of hot water leaking out of the center exhaust port that leads into the log manifold. When hot enough, it steams. When I feel underneathe, there's a hole there with threads and it seems there is a bolt missing. I say...
  18. D

    Short il filter vs Long oil filter chry 360

    needed a replacement oil filte needed a replacement oil filter for a chry 360 but all I could find last weekend was a short fram filter. it fits fine but it's about half the length of the regular sierra 7875's or napa 1515's. same diameter though. Any problems with keeping thie fram in...
  19. D

    Zincs for Heat Exchanger chry 360

    "for the heat exchangers on my "for the heat exchangers on my 360's (the L shaped ones), do I need to drain everything to change the zincs? Never done this before. Also, where are the threads for the zincs - are they on a vertical piece of the unit or horizonal piece. Thanks all"
  20. D

    Carter carb find model#

    "looking to replace my 1976 ca "looking to replace my 1976 carter afb's and was wondering how i can locate the model number before I order a replacement. not at my boat for a few days but when i get there, is it stamped on the metal somewhere? maybe under the flame arrestor? any help would...
Back
Top