Logo
FULL SITE MENU

Recent content by goosemasterkl

  1. G

    25 hp Johnson outboard engine help!!!!!!!!!!!

    It's Johnson 25hp model# J25RSSE. A 2000 year model with manual start. I ordered a new fuel nipple but the one on the carb is really set in there. Would a straight punch work the best getting it out? Thanks
  2. G

    25 hp Johnson outboard engine help!!!!!!!!!!!

    It was brought to me with the hose off. Where does that hose hookup at? Would it be a problem if I couldn't get it out and replaced? Can you buy that piece? Thanks
  3. G

    25 hp Johnson outboard engine help!!!!!!!!!!!

    I've been cleaning this carburetor up and putting news parts inside and the nipple broke off in the picture that is circled. I'm wondering what is that part for and how do you replace them? I tried removing the broke one but it is in there pretty good. Any suggestions or comments would be...
  4. G

    12' Pontoon/Fishing boat issue!!!!!!!!!!!!

    He's tried that too. Would the length of the shaft cause this problem? Long shaft vs. Short shaft motor?
  5. G

    12' Pontoon/Fishing boat issue!!!!!!!!!!!!

    Asking for a friend of mine who has a 12' pontoon/fishing boat with a 3.5 hp Mercury 4 stroke outboard. The issue he's having is that when he tries to power up the engine to take off the front of the boat wants to go down under the water. He's messed with how the trim is set and nothing will...
  6. G

    Mercury 3.5 hp 4 stroke repair help!!!!!!!!!!!!!

    I've changed the water pump kit out with new impeller but I can't get the shaft and everything back up in the tube. The brass line that runs the length of the housing is just floating around in there and getting the shaft gears to line up to go back in then the water line wasn't in the water...
  7. G

    Mercury 3.5 hp 4 stroke intermittent tell tale discharge!!!!!!!!!

    I'm trying to help a friend of mine figure out why the tell tale will put out water for a little bit then will stop working for awhile then back working again. Can someone tell me what and where to look to find the problem? The motor is a 3.5 hp 4 stroke Mercury. Thanks in advance to anyone who...
  8. G

    2000 Johnson 25hp carburetor help!!!!!!!!!!!!

    What are those lead shot plugs for?
  9. G

    2000 Johnson 25hp carburetor help!!!!!!!!!!!!

    The guy told me that when he got it out to run it that it started up but it was sputtering and then it would die.
  10. G

    2000 Johnson 25hp carburetor help!!!!!!!!!!!!

    I'm wanting to rebuild the carburetor that is below and I have a couple questions. The carburetor's part number is 5000883 and the number on the carb shows HY432700. The 2 circles is showing what they're calling lead shots in the parts diagram. My questions are. Do you take these out when you...
  11. G

    Johnson 25 hp help!!!!!!

    These are what I'm referring to. Do these need to be removed for cleaning and rebuilding the carburetor? If so' how do you remove them and install them? Thanks
  12. G

    Johnson 25 hp help!!!!!!

    I meant to ask someone; The last picture I posted of the top of the carburetor. Do you have to remove those lead shots when cleaning/rebuilding the carburetor? There's one on each side of the welch plug and another one on the side. Just wondering and if so; how do you go about removing them and...
  13. G

    Johnson 25 hp help!!!!!!

    Thanks very much to all who replied.
  14. G

    Johnson 25 hp help!!!!!!

    Where can I go to see an IPL so I can see parts breakdown and part numbers? Thanks
  15. G

    Johnson 25 hp help!!!!!!

    Here are the pictures. I finally figured out how to upload them I think.
See more
Back
Top