Logo
FULL SITE MENU

Search results

  1. 2

    2001 Yamaha Z200 hpdi manual

    Finding a lot of 2000 year manuals (Y) but no 2001 (Z) designator on end of model number. Looking online for a factory manual only. Is one as good as the other for my engine? Thanks
  2. 2

    60elpto oil injection

    My son has a 60elpto sn 0g099787 that he has recently acquired. We have performed the usual maintenance and it is running on premix and the oil tank at present. Is it desirable or possible to delete the oil injection on this model and premix only. I welcome your thoughts Thanks 208
  3. 2

    1976 Evinrude 200

    I have acquired 76 200 Evinrude. Seems to be unmolested. Not stuck and looks pretty good. Worth spending any money on? Reliable? Thanks ps I like old stuff
  4. 2

    Serial Number G3306194 ID

    Trying to help a friend ID his motor. This motor does not have an idle needle valve. It has an extra air bleed orifice on the carbs. was sold as a 98 175 but I cannot find any parts listings that show this engine without a idle needle valve. Serial number on exhaust hump casting plug is...
  5. 2

    Exhaust coming from flywheel housing.

    Good morning, Trying to help a friend with his supposedly 98 175 looper ois engine. ( there is no data plate). Long story short there is a hole in the flywheel housing and a good bit of exhaust smoke is coming out when running. I can pull the number 1 cylinder plug wire and the smoke...
  6. 2

    1986 evinrude 50 hp power pack

    Hello all, I have a bad power pack apparently. Do I need to order the BRP oem part or will a CDI brand suffice? Good voltage from charge coil using DVA and 9 volts from sensor coil. No output to either coil. Running one minute and just shut down. Thanks
  7. 2

    Correct thermostat springs?

    Recently, I replaced the thermostats on my J150EXEOM. The new springs did not come in a BRP package and were noticeably weaker than the red ones that were replaced. Is this a problem? Idle temps are about 135 F on both banks. Thanks
  8. 2

    Checking fuel pressure

    Can I attach a pressure gauge to my schrader valve on J150EXEOM and see a reading at wot? I used a clear hose to check at idle but am a little apprehensive about bouncing down the river while this is connected. Thanks, 208
  9. 2

    Tachometer Reading Low

    On my J150EXEOM I have a low tach reading at all engine speeds. Verifying actual engine speed with a Blue Point photo tach, I am reading 150 low at idle, 400 low at 2400, and 1000 low at 5000 Rpms. This is a recent development. Using the factory manual, I found that the grey wire is putting out...
  10. 2

    Lower bearing to upper bearing hose

    Happy fathers day I have. J150EXEOM that I am restoring the recirculating system on and thought that while I'm at it will make sure the lower to upper bearing plumbing is correct. is there a check valve between the two or does it free flow back and forth? Mine seems to free flow. I have a...
  11. 2

    Throttle bodies not matching

    After a year of trying to get my J150EXEOM to idle smoother, I have discovered a difference in the bore size and butterfly relief cuts in my throttle bodies. This is apparently an engine put together from parts of other engines. part numbers on all 6 carbs are 436797 and the bores measure...
  12. 2

    OIS Timing Adjustment

    On my 1995 J150EXEOM I noticed that after setting idle and WOT timing with the factory Ignition Analyzer, both tabs are all the way to the left. I did use the factory manual to set timing pointer first. Thank all who contributed in getting this boat on the water! Chip
  13. 2

    Timer Base Compatability

    I am trying to get a E140TXCD running. I bought this engine not running with good compression for a cheap price and #2 cylinder is not firing. One of the coils in the timer base is open. I would like to buy a used one on line to get this engine going. it is a 1986 model. The timer base has...
  14. 2

    Spark Plug Type

    I have a J150EXEOM, the factory manual recommends QL77JC4 CHAMPION plugs. I notice that some sites list QL78YC as an option. Which plug should I be using for general recreation? Thanks
  15. 2

    Tachometer Reading

    Hi All, I am new here but have been lurking awhile. Lots of good info, thanks! The other day, I was monitoring my engine (1995 Johnson 150 looper) with a clamp on digital tach and noticed that if I connected to 1,3, or 5 the reading was 650 rpm or so. If I connected to 2,4,or 6 the reading...
Back
Top