Logo
FULL SITE MENU

Search results

  1. R

    Dt140 starting/drive ability problem

    A friend of mine brings me his boat the other day to see if I can fix it but I'm stumped. He had it at a shop and they thought it was the stator but I don't know how you would test it. He says the boat won't propel itself very well in the water. So when I got it I couldn't get it to fire and...
  2. R

    1978 mercury m-900 engine problem

    Today I was out on the lake fishing and when I went to head back to shore I started my boat and began to head in when all at once it started to loose power and died. I primed it up again and it took off only to do the same thing 50yds later. I had my buddy prime it up again and he had to keep...
  3. R

    1978 Mercury M900 starter question

    About a week ago I tried starting my boat and the starter wouldn't engage the flywheel so I tapped on the starter with a hammer and then it worked. I tried to start it again and same thing happened by the 3rd go around the started completely stuck wide open and I couldn't get it to shut off and...
  4. R

    1978 90hp merc jetting question

    I would like to put bigger jets in my m900 carbs to make it a 115hp motor but not sure on which jet to get. Can anyone help me out. Is it a .074 jet I need?
  5. R

    Why does my prop turn all the time???

    1978 90 hp merc motor. I just changed my water pump in my boat and when I had it on the hose I realized the prop turns all the time even in neutral. I just put this motor on my boat so could it be that something isn't hooked up right or it's out of adjustment? If so what should I check? Thanks
  6. R

    Pre 80s merc 90 hp doesn't pee at idle

    I can't remember what yr this motor is maybe a 78-79 not sure. My motor doesn't pee when it idles but if I speed it up it will start to pee. I blew compressed air into the hole to make sure nothing was obstructing. Is the impeller going out. I was thinking I sucked up sand in it but I just put...
  7. R

    Evenrude fisherman 6hp. Need help finding serial numbers

    I have a motor that could use a few parts but the ID tag is gone from the side. is there anyway to figure out the year of it? I came up with 1966ish just by searching the parts catalog on here but want to know for sure before I order parts. thanks
  8. R

    Dt 115 carb question

    I recently bought a boat from a guy and I can't get it started. So far I've checked compression which is anywhere from 100-90psi. I took the carbs apart and did a quick spray down with carb cleaner and without replacing or taking any parts out of the carb. If I spray a shot of carb cleaner in...
  9. R

    93 Suzuki dt115 question

    Can someone look at this link and tell me what's missing from the head on this motor please? http://forums.iboats.com/yamaha-suzuki-outboards/1993-suzuki-dt115-question-589798.html
  10. R

    Adding power trim to a non-power trim boat. Need a few questions answered

    I have a 1982 evenrude 75hp boat without power trim and recently purchased a power trim unit with a 2-wire motor (green & blue wires) a relay box that has a 2wire round connector with a flat spot in it, a 5-wire connector with a flat spot in it, another 2 wire (green wires going to each relay)...
  11. R

    I need help hooking up a power trim

    I have a 82 evinrude 75hp motor that doesn't have pwr trim and I want to put it on. I bought a pwr trim for it but don't know what else I need besides the thumb switch and throttle control nor do I know how to hook it all up an make it work lol. Thanks
  12. R

    Best decal remover???

    well tonight i remembered i had a 3m erase wheel in my tool box so i did a little test with the aircraft spruce erase wheel and the 3m. the pic on the left is the 3m that was used before i started my project on this boat and was alittle bit bigger than the NEW aircraft spruce wheel on the right...
  13. R

    Best decal remover???

    I need to remove all the pinstripe and decals off a boat and was wondering the best and quickest way to do it. I have a decal removal wheel from aircraft spruce but it's taking some time to do it all. I have half the boat done on one side and the wheel is 1/2 gone. I have a wide stripe I'm...
  14. R

    no WOT

    ok i actually got the motor to run the way it should except it kinda spudders and pops son now ill have to see what that is, prob the carbs need a good cleaning here is some pics of the linkage if anyone sees something wrong they could tell me. and im also needing to get this 6hp motor up and...
  15. R

    no WOT

    no my doesn not have a kill switch on it
  16. R

    no WOT

    i didnt appy voltage to it, it was already there. i checked the wire before i start it and its dead and after i start it, it has voltage that slowly drops. heres what wires i have left on the switch
  17. R

    no WOT

    I Have a 82 evinrude 75hp and it has no wide open throttle. when you rock the throttle fwd the butterfly's dont move and the throttle cam rocks toward the prop side of the engine if that makes any sense. if you hit reverse the butterflys open up. i havent actually had the motor running yet but...
  18. R

    Low compression. Help. 82' evinrude 75hp

    I traded a car trailer for a couple of boats that need work from a guy and tonight I got around to seeing how the engine was on the one boat because he said the guy he got it from said it runs but has no WOT so I checked the compression on it and it has 120 on one cylinder and 95 on the other 2...
  19. R

    Carb Sync question

    I have a bf25a that I cleaned the carbs on but need to sync them now cuz there way off now so I ordered The "Emgo Carburetor syncronizer But how or where does it get hooked at? I see 2 possible spots but one hose is for fuel so does it get hooked in line with the other hose on the carb or do I...
  20. R

    1997 Honda 25hp 4stroke problem

    heres how my timing marks are now why would i all of a sudden have no compression
Back
Top