Logo
FULL SITE MENU

Search results

  1. C

    vro pump rebuild and testing procedures please

    so i have another post for engine issues i guess cyclinder 4 is running lean but dont know how to set it but i waited 2 1/2 weeks or so for a VRO pump rebuild kit from china i rebuit it.. but i guess its not pumping the gas.. and they give you a small o ring.. and there is another o ring...
  2. C

    e115mlcrd buzzer goes off goes faster if rpms increase

    hi i rebuilt my engine from scratch a couple years ago and then had a marine place get the rpms to run properly found it had bad wiring... but i never got it in the water and engine still hasnt been broken in yet.. so i i just got around to testing it on ears she doesnt like to run first...
  3. C

    1984 115hp and i wanna use Deep Cycle

    hi I have a 115 1984 engine and I wanted to use my deep cycle battery to run on it.. but I seen now off the page for replacement rectifiers/voltage regulator I can not use a deep cycle battery.. why not and the I have the mini kota MC2 dc battery charger wanna use with.. so if I cant use...
  4. C

    how do you check a Trigger Base Adjustable Linkage??

    hi i like to know how do you check the proper length of the Trigger Base Linkage to the throttle... most are fixed linkage not adjustable but on my engine here its adjustable and it had the stop nut loose... my question is how do i check that it is in the right position since i still havign...
  5. C

    40hp 402 timing questions?

    hi i posted in past about my 402 engine as it stalls when you punch it and i have dicked around 6+ hours adjusting the damn fuel mixture screw doing like 1mm turn and sitting for 10 seconds nothing frigin works.... the marine is 4 weeks behind so i figure i might as well tackle it.. i posted...
  6. C

    40hp 402 Engine hickuping and gutless

    hi I have a 40hp 402 engine.. I put a new carb kit in... I checked the filter its clean I checked spark I got lots but the engine doesn't wanna idle and when I rev higher in neutral she hickups kick backs and cant rev fast... what be wrong what can I do I even adjusted the idle screw...
  7. C

    v-200 doesnt shift into gear stays in neutral

    hi last year i worked on this v200 engine as i was driving it and noticed it over heating and no tell tail water stream water pump so end of season i replaced the water pump and in april of this year i tested it in my box and it worked... but today i finally got around to testing it...
  8. C

    84 115 cant get it to fire up

    so i finally got a chance to put my rebuilt engine in a box to test and break in the engine but she wont fire she sputs my friend figured its flooded i dont know didnt know you could flood these engines?? i have tried carb cleaner in the intake also i did a water bottle with mixed...
  9. C

    84 115 finally going to break in engine, but couple questions

    hi reading my book for breaking in the engine I says during the first 10 min to operate the engine in gear at fast idle... but you cant lift that high idle lever in gear.. or put it in gear after you lift it up so what do they mean and I just going to test it in a test box I have with...
  10. C

    84 115hp evinrude.. shift cables having problems..

    hi I re assembled my remote control and testing it back and forth but the one cable jams inside I guess at the end I hear it binding and scraping... I looked on this site for the shift cables under the remote control but there is no cables for it.... can you still get the shift cables for...
  11. C

    84 115hp evinrude... does teleflex make a Temperature kit for this engine

    hi does Teleflex making a temperature sending unit and gauge kit for this 84 115hp evinrude... as the new company seastar doesn't tell you nothing about it as for my mercury engine it came with Z bend a triangle bracket the sending unit and the gauge from Teleflex... but not sure if they...
  12. C

    84 115hp evinrude... possible buzzer broken?

    hi I rebuilt my engine from scratch and the remote control I figured id test the buzzer by the by the temperature over heat senders by just runninging a jumper wire from that quick connector to ground of the engine all it does it sparks the my jumper wire and I hear kinda the buzzer clicking...
  13. C

    Faria Speedometer not working

    hi I have a speedometer on my boat by Faria it doesn't work in the water... if I put my mouth on the hose and blow it doesn't work if I put compressed air on the end it works I have pulled the hose off at the gauge and blew air through but still doesn't work in water and the white lever...
  14. C

    84 115 need a temperature sending unit,

    hi In an earlier post I was going to mount the Faria surface mount temperature sending unit.. but its having issue trying to get it a good smooth contact.... I contacted Faria and they don't make another type just ones that Screw into the water jacket I did ask for ohms for the readings...
  15. C

    84 115 remote control i want to change the trim switch

    hi I cant seem to take this unit apart I tried taking the 3 screws and the center screw out I can split the housing some but it doesn't come apart I then tried just prying the plastic cover off but couldn't get it to pop off before I break it what is the procedure to get the housing off to...
  16. C

    84 115 evinrude is there a good break down of the water pump assembly?

    hi i dry fitted and such the water pump but my spline O Ring is much bigger it seems also i have an extra O Ring in the kit this is for the 1984 115hp evinrude now on this site it doesnt show the updated water pump but on...
  17. C

    84 115 evinrude bought a Temperature Gauge and sender, is there a good spot to modify it

    hi so i was at the marina yesterday picked up the Faria Temperature gauge and sending unit.. paper says just take off a head bolt and then you just rest this thing against the housing etc... but my head bolts are recessed down from the cover... i looked for a couple of spots on the block...
  18. C

    spline grease substitute and water pump glue?

    hi for the 115 i wanna put the lower half up and i watched video and it talked about putting spline grease on and gluing the water pump seal and the stainless cup in place what substitute is for spline grease? for the chrysler engine all i did was put gray anti seize on is that ok?? or...
  19. C

    84 115 evinrude exhaust housing to mid section, can you use Anaerobic to glue the 2 halves

    hi so there is no gasket for the exhaust housing and the mid section motor leg... i read some places use permatex black RTV silcone.. i was thinking can i use the Red Peramatex anaerobic sealant since a gasket doesnt exisit for this part
  20. C

    84 115 evinrude is there a proper wire diagram?

    hi i trying to re plug in and route the wires and there was a few connections i cant figure out yet now looking at things the selco book shows this engine doesnt use a regulator just a rectifier on the max rules site the image similar to this one is one without Tilt trim but uses a...
Back
Top