Logo
FULL SITE MENU

Search results

  1. W

    1987 evinrude 88 hp ignition problems

    I have a 1987 88 hp evinrude the two bottom plugs dont seem to be firing right. There is volts getting to coil and to spark plug, but the two bottom plugs dont seem to be making a difference when you take the plug wires of of them. I tryed crossing the wires on the coils but it will still be...
  2. W

    1986 mercury 45 hp carb problems

    I have this classic 50 that when you are trollling at slow speed it will choke down and die, and then you have to choke it once to get it to crank and if you choke it more than once it is hard to crank. it will run pretty good on top end. I have cleaned the carbs and checked fuel pump and it...
  3. W

    1988 yamha pro v 150hp carb

    I was wondering if someone could tell me how to adjust carb on the 150 pro v 1988, where do you start, is it one and a hallf turns out from seated or what. I was going to take mine off and clean them an was wondering if someone knew, before i start, they want to bog when you start off, but does...
  4. W

    1986 mercury 45 hp carb problems

    I was just wondering why no one answers any questions I ask in here, because I have asked several questions before and never got answer. except maybe one time.
  5. W

    1986 mercury 45 hp carb problems 1986 45 hp

    I bought a 1986 mercury 45 hp and it will run good when you first start out and on top end does good but when you start to troll the carbs will load up and choke down and then its hard to crank back up hard to start off without going dead. I have cleaned carbs and put new needle in but not...
  6. W

    yamaha pro v 150hp 1988 carb adjustment

    could anyone tell me the procedure for adjusting carbs on a1988 150 I just bought and had carbs cleaned just wanted to check it because it has a little skip when idling
  7. W

    1988 pro v 150hp prop shaft

    how hard is it to change a prop shaft on a 150 pro v? I just bought this motor and prop shaft is warped, but I have another one to put on. Can anyone tell me if its possible for me to do it. Is ther a site you can go that will show you how. I dont have a manuel yet. I have took the older...
  8. W

    1987 yamaha 150hp compression

    A friend of mine has a 150 yamaha 1987 model outboard and I was wandering what a adaquate compression would be on that old of a model. he said that it was running about 95 and 100 psi is that ok?
  9. W

    1973 evinrude 50 hp not firing

    i bought this motor not running but it has 135 pounds compression on each cylinder I tested the stator with dva tester and it was putting out 250 volts going into power pack the ohms on the trigger seem right. but there is no fire coming out to either coil, i put new power pack an new...
  10. W

    1995 50 hp force switch wires

    i have a1995 50hp force i bought the engine but someone took the switch off and i dont know which wires goes to key switch can anyone help, i could guess but would take a while. there are wires going out of contol box ,i know some of them go to switch. can anyone help
  11. W

    1987 70 hp johnson carbureator problems

    I have this 87 70 hp evinrude it has good spark good compression 120 on all cylinders it sit up for a while couple years.I took carbs off and cleaned them twice. because it would run good but when you put it in the water it would just die as soon as you put it in gear. but on land it would run...
  12. W

    1989 43 water in oil

    "I just bought this bought fro "I just bought this bought from a guy, who said it didnt have water in oil last fall, but said his mechanic winterized it for him. but when he cranked it just before i bought it, and ran it little while checked the oil and had water in it. I pulled the exhaust...
  13. W

    How can you tell 43 boatmotor or truck

    i am looking for 4.3 boat moto i am looking for 4.3 boat motor but a mechanic told me not to buy a truck motor but make sure it was a marine boat motor. how can you tell for sure?
  14. W

    2001 tahoe 43 engine alpha 1 gen 2

    "I just bought this boat it ha "I just bought this boat it had a 4.3 alpha 1 gen 2 motor and outdrive, but motor and outdrive were taken completely out, because motor was bad, and i think he sold outdrive off of it. my question is will a 1989 4.3 work and will a alpha 1 gen 1 work in the same...
  15. W

    1990 50 hp force wont go in gear

    "I just got this boat and when "I just got this boat and when it aint running it will go in gear fine, forward and reverse but when running it wont go in forward but it will go in reverse checked oil just a couple little fragments on magnet could there be some linkage problem, I dont know much...
  16. W

    1991 ford 23 motor

    "I was looking at buying a 2.3 "I was looking at buying a 2.3 ford motor in a 17 ft ski boat is this A 120 HP AND ARE THEY VERY RELIABLE , do they have much power, is there something to look out for on these engines"
  17. W

    1987 70 hp johnson low spark

    "I just got this boat the othe "I just got this boat the other day, it cuts out when running , i checked the spark all three plugs seems to just barely have a spark, i checked fire going into coils not much going in either , but had fire from stator close 200 or 250, trigger checked out ok ...
  18. W

    1987 70 hp johnson carbureator problems

    "I just got this motor it sit "I just got this motor it sit up 3 or 5 years I cleaned carbs and it cranks right up, but it will start idling real fast by itself i tried adjusting idle but its like you are giving it the gas and idles up by itself and when you race it up sometimes it dont want...
  19. W

    195960 35 hp evinrude loss commpression

    "I just got this motor the oth "I just got this motor the other day, and it had been set up for a few years, I cleaned carbs and sanded points poured oil in sparkplug holes and used break away spray, got it to crank. ran fair but had a little skip to it. so I checked compression top cylinder...
  20. W

    70 hp 1977 evinrude carburator

    "I have a 70 hp 1977 evinrude "I have a 70 hp 1977 evinrude and when you choke it the butterflys dont go back like they were and you end up having to take the cowl off and pull choke back by hand. the choke selnoid is not holding it eiher, cant see why it wont go back anyone know. thanks"
Back
Top