Logo
FULL SITE MENU

Search results

  1. S

    Powerhead Question?

    Will a 35hp Johnson powerhead, model #J35RCTS work on a Evinrude 25hp, model#E25RCIM? They both use the same powerhead to crankcase gasket. I wanted the forums outboard motor experts opinions before I invest my money and time on this project. Is there any detail I may have overlooked please...
  2. S

    1981,Evinrude,25hp,Model#E25RCIM Spark Problem

    I have a 1981,25hp Evinrude,Model#E25RCIM, that is firing on one cylinder only.I was driving back to boat dock wide open throttle when engine died suddenly.I had just replaced a charging coil under the flywheel reccently[last 6 months], to fix a firing on one cylinder problem.Can the coils...
  3. S

    Lower Unit Propeller Seal Replacement????

    About how many(approximately) labor hours would it take a compotent marine repair shop to complete this repair job????And any more additional problems that might be encountered, thank you,"The SturgeonGeneral."
  4. S

    Hard Starting 1981, 25hp, Evinrude,Model# E25RCIM.

    My motor is hard to start, and at WOT is reving(RPM's increase and decrease).When I turn the throttle grip harder (more pressure;force) on the tiller handle it will start (easier).There is no more gear teeth on the pinion throttle gear in the tiller handle to get a little more gas for easier...
  5. S

    Water In Gearcase Oil

    I have a 1983 ,25 hp,Evinrude,model#E25RCIM,that has a leak I think around the bottom gear housing case cover or around propeller shaft.The propeller shaft from a visiablly veiwing doesn't appear to be bent.My question is it possable to remove the bottom gearcase cover and replace the spagetti...
  6. S

    25 HP Evinrude Kill Switch

    I have a 1981 25HP Evinrude, that had a stop button (kill switch) that was not working, so I removed it and instead of replacing the stop button, I have been using the full choke knob to kill the motor.Will this damage the motor in anyway?"The Sturgeon General".
  7. S

    Oil Drain Screw Thread Damage

    I have oil drain screw damage on my exhaughst housing case on my 1981 Evinrude ,25HP.Water leaks into my lower gear case oil and I need someone to tell me what my options are for repairing this problem,Thank You "The Sturgeon General".
  8. S

    Steps For Pressure Testing Lower Unit?

    I have water in my 1981,Evinrude,25hp,#E25RCIM, lower unit oil.I have been using it still what can I expect in damage and can I get away with one or more trips before fixing?It appears to be leaking a little around the propeller.I don't want to mess around with the gears in lower unit,does...
  9. S

    25hp tiller handle used part needed!!

    If anyone has a old 25hp Johnson or Evinrude parts motor 1978 through 1985, I need a "PINION"(BRP-Parts#0303142) with a set "SCREW"(BRP-Parts#0303951) which controls the engine throttle.I will pay a reasonable cost for this part or a complete used tiller handle.My engine specs are 1981...
  10. S

    Used 25hp evinrude part wanted

    I'm looking for a "PINION", (BRP-Part#0303142).I have a 1981,EVINRUDE,25HP,ROPE START,MODEL#E25RCIM ,outboard.The "Pinion", is located in the back of the tiller handle and has a set "SCREW",(BRP-Part#0303951),and controls the throttle when you twist the tiller handle throttle grip.One of the...
  11. S

    Checking for a leak in gearcase oil 1981 25hp

    I have a 1981,25HP Evinrude,Model#E25RCIM,that has water in gearcase oil.How do I go about pressure rising the gearcase to look for the leak?What tools and instruments would be needed?Any advice or information would be greatly appreciated "The Sturgeon General".
  12. S

    Steps of action for a submerged 1981 25 HP Evinrude

    "My boat sank in fresh water w "My boat sank in fresh water with a 1981, 25 HP,Evinrude attached to its transom.I need information on what needs to be done after retrival,thanx The Sturgeon General."
  13. S

    Spark Plug Gap Setting 1984 6 hp

    "Engine Specifications:1984 Johnson 6hp Model#J6RCR I've been using L77JC4'S Gapped at.040.Source for information "Outboard Motor Service Manual 10th Edition" by Intertec.I never had a problem starting the motor in the past,1st or 2nd pull.Lately 10 or more pulls kind of embarassing at boat ramp...
  14. S

    Powerhead Removal Question

    "I have a 1972,20HP, Johnson, "I have a 1972,20HP, Johnson, Model No.#20R72R that I need to remove the powerhead from so I can replace the gasket and fix broken motor mounts and loose cowling.I want to leave carborateur,fuel pump,flywheel and etc. mounted to powerhead if possiable? I have...
  15. S

    TILLER ARM THROTTLE HANDLE INSTALLATION

    "Hello, everyone on the discus "Hello, everyone on the discussion board,and a special hello to Joe Reeves, who has helped me so many times in the past.Its been a long time since I last posted.I have a 1972 20HP,Johnson,manual start,Model#20R72R that use to be setup as a electric start with...
  16. S

    It Was All My Fault

    "I couldn't get my battery "I couldn't get my battery connected to my starter motor on my 35hp,Johnson to turn the flywheel fast enough to start the motor the other night.I had 3 charged batteries that couldn't turn flywheel fast enough to start my outboard but any of the 3 batteries had no...
  17. S

    New Problem Starter Motor Too Slow

    "Well I installed the Perma Co "Well I installed the Perma Coil wasn't sure of spark plug depth so I snipped the insert down to 3/8" depth to be safe.Installed the spark plug and it was was tight and strong,just like new.So I thought I"D go fishing since I had synchronized the motor and...
  18. S

    HeliCoil Size Double Check

    "I wasn't able to locate t "I wasn't able to locate the original helicoil spark plug rethread kit.All I could find is a company by the name of Perma-Coil thread kits(spark plug).I purchased the kit with 14mm x 1.25mm x 1/2" spark plug inserts.I was told by the salesman, once the insert is...
  19. S

    Spark Plug Help

    "Well the last time I posted i "Well the last time I posted it was a water pump problem,I'm happy to report that I decided to give it one more try before tearing into the cylinder head.I clamped on the dog ears real tight to make a better seal and fired the motor up and the water started to...
  20. S

    WHAT ARE WATER RESTRICTORS

    "Since I had no replys to my m "Since I had no replys to my most recent post,I'll look for answers in a more basic simple manner.Lets start with I have a powerhead of a 1983,35HP,long shaft,manual start,Johnson,model no.#J35RCTS.I suspect has internal water flow(circulation)problems,affecting...
Back
Top