Logo
FULL SITE MENU

Search results

  1. S

    2001 Merc 150 Carburated

    Hello all.... I recently purchased a used 22 foot Cape Craft with a large walk in center console. It has a 2001 Carbureted 150 on the back. The boat alone weighs around 2700lbs. It has a 70 gallon tank. Should this motor be enough? It takes a long time to plane.....sometimes I back off the...
  2. S

    1993 Evinrude 225hp Ocean Pro Bogging Down

    This is bothering me to death! My problem is bogging down during acceleration. The motor will start and idle like a champ. Has new plugs, new fuel filters and thats it for now. If i hammer it at idle, it just doesn't sound right, and when I let off, it will stall. It will start right...
  3. S

    1993 Ocean Pro 225hp Powerhead Removal

    Need to take the powerhead off to fix the upper mount. There are two sets of bolts and I am confused of which to take off. There is a set which is shorter and are at the top of the exhaust housing, right above the rubber seal, and there is a set which are a little longer which also look like...
  4. S

    19'93, 225 Bogs Down Please Help!

    I have a 1993, 225 Ocean Pro that has run very well up until last week. I am able to go soft up to about 4500 rpm's, anything over that and it bogs down. If I hammer it out of the whole shot, it just bogs down immediately. It starts and idles fine. New filters this year. It ran fine the...
  5. S

    When it rains, it pours 1993 225

    I have a 1993 Evinrude Ocean Pro, 225. Put the boat back in today to go fishing. I'd be travelling at about 5500 rpms and it would bog down, but not stall out. I would bump it back into neutral, and start again. If I went from neutral to wot, it would bog, but if I slowly moved it up to 4000...
  6. S

    1993 Ocean Pro 225hp Flush out

    When I take the boat out of the water, I flush the motor for about 15 minutes. I take out the tell tale, and hook up the hose. When I am finished, and unscrew the hose, water shoots back out the hole as if it is under pressure. Shouldn't it just drain out the bottom, or is there pressure when...
  7. S

    Nissan 12 hp circa b97

    "I have posted this here on th "I have posted this here on the evinrude forum because I know it gets more traffic, and I believe this would be the same diagnosis for either engine. I have a 12 horse Nissan kicker that appears to run great. I am just worried about one thing. As it idles, it...
  8. S

    Nissan 12 hp circa b97

    "I have a 12 horse Nissan kick "I have a 12 horse Nissan kicker that appears to run great. I am just worried about one thing. As it idles, it kicks, or jumps to the right (when looking from back, by the pull start toward the prop side) at a regular interval. It is similar to the kick it...
  9. S

    Water Pressure 1993 225 Ocean Pro

    "This year I changed the impel "This year I changed the impeller and noticed a much higher water pressure. I know the impeller is what caused this, but what amount of pressure is too much, and what can happen? It gets above 30 psi at wot."
  10. S

    Power to positive bus

    "Is it common to be able to tu "Is it common to be able to turn on lights as soon as the battery switch is on, or is it usually when the key switch is on? If its when the key switch is on, what wire goes from the switch to the bus bar giving power to everything? Right now, I have a the common...
  11. S

    Water Leak

    "I posted a question on the Lo "I posted a question on the Lower Mount yesterday. I got a better look today and have taken a pic to see if it helps explain. I have great water pressure to the guage, and lots pouring out of the tell tale. However, by the lower mount, there is cold water...
  12. S

    Rubber Lower Mount

    "What is it for? Its number 1 "What is it for? Its number 18 in the diagram. Also When in a tank, water comes out from behind it, is this supposed to happen? Mount
  13. S

    1993 225 where is shift rod connected

    "I need to take the lower unit "I need to take the lower unit off to change the water pump....have never done this before. I am a subscriber of SelocOnline, but the picture is awful, I can't see where it points to when showing the nut that needs to be removed to disengage the shift rod. Can...
Back
Top