Logo
FULL SITE MENU

Recent content by ryans01z28

  1. R

    Dt140 starting/drive ability problem

    A friend of mine brings me his boat the other day to see if I can fix it but I'm stumped. He had it at a shop and they thought it was the stator but I don't know how you would test it. He says the boat won't propel itself very well in the water. So when I got it I couldn't get it to fire and...
  2. R

    1978 mercury m-900 engine problem

    Today I was out on the lake fishing and when I went to head back to shore I started my boat and began to head in when all at once it started to loose power and died. I primed it up again and it took off only to do the same thing 50yds later. I had my buddy prime it up again and he had to keep...
  3. R

    1978 Mercury M900 starter question

    About a week ago I tried starting my boat and the starter wouldn't engage the flywheel so I tapped on the starter with a hammer and then it worked. I tried to start it again and same thing happened by the 3rd go around the started completely stuck wide open and I couldn't get it to shut off and...
  4. R

    1978 90hp merc jetting question

    I would like to put bigger jets in my m900 carbs to make it a 115hp motor but not sure on which jet to get. Can anyone help me out. Is it a .074 jet I need?
  5. R

    Why does my prop turn all the time???

    1978 90 hp merc motor. I just changed my water pump in my boat and when I had it on the hose I realized the prop turns all the time even in neutral. I just put this motor on my boat so could it be that something isn't hooked up right or it's out of adjustment? If so what should I check? Thanks
  6. R

    Pre 80s merc 90 hp doesn't pee at idle

    I can't remember what yr this motor is maybe a 78-79 not sure. My motor doesn't pee when it idles but if I speed it up it will start to pee. I blew compressed air into the hole to make sure nothing was obstructing. Is the impeller going out. I was thinking I sucked up sand in it but I just put...
  7. R

    Evenrude fisherman 6hp. Need help finding serial numbers

    I have a motor that could use a few parts but the ID tag is gone from the side. is there anyway to figure out the year of it? I came up with 1966ish just by searching the parts catalog on here but want to know for sure before I order parts. thanks
  8. R

    Dt 115 carb question

    I recently bought a boat from a guy and I can't get it started. So far I've checked compression which is anywhere from 100-90psi. I took the carbs apart and did a quick spray down with carb cleaner and without replacing or taking any parts out of the carb. If I spray a shot of carb cleaner in...
  9. R

    93 Suzuki dt115 question

    Can someone look at this link and tell me what's missing from the head on this motor please? http://forums.iboats.com/yamaha-suzuki-outboards/1993-suzuki-dt115-question-589798.html
  10. R

    Adding power trim to a non-power trim boat. Need a few questions answered

    I have a 1982 evenrude 75hp boat without power trim and recently purchased a power trim unit with a 2-wire motor (green & blue wires) a relay box that has a 2wire round connector with a flat spot in it, a 5-wire connector with a flat spot in it, another 2 wire (green wires going to each relay)...
  11. R

    I need help hooking up a power trim

    I have a 82 evinrude 75hp motor that doesn't have pwr trim and I want to put it on. I bought a pwr trim for it but don't know what else I need besides the thumb switch and throttle control nor do I know how to hook it all up an make it work lol. Thanks
  12. R

    Best decal remover???

    well tonight i remembered i had a 3m erase wheel in my tool box so i did a little test with the aircraft spruce erase wheel and the 3m. the pic on the left is the 3m that was used before i started my project on this boat and was alittle bit bigger than the NEW aircraft spruce wheel on the right...
  13. R

    Best decal remover???

    I need to remove all the pinstripe and decals off a boat and was wondering the best and quickest way to do it. I have a decal removal wheel from aircraft spruce but it's taking some time to do it all. I have half the boat done on one side and the wheel is 1/2 gone. I have a wide stripe I'm...
  14. R

    no WOT

    ok i actually got the motor to run the way it should except it kinda spudders and pops son now ill have to see what that is, prob the carbs need a good cleaning here is some pics of the linkage if anyone sees something wrong they could tell me. and im also needing to get this 6hp motor up and...
  15. R

    no WOT

    no my doesn not have a kill switch on it
See more
Back
Top