Logo
FULL SITE MENU

Recent content by paul_m_in_nj

  1. P

    E25DTL from tiller to remote

    I just began the switch to remote control from tiller. The Etec has tilt and trim and the remote control conversion kit (P/N 5007742) says I need to connect to a Tiller sending Unit. I don't know what that is. What is that?!. Thanks Paul
  2. P

    Evinrude ETEC E25DTSLINC

    I am about to remove and replace the vapor separator in my ETEC. I have the correct service manual. any advice before i start? Thanks Paul
  3. P

    2012 ETEC 25 HP Trim Relay?

    I need to replace the tilt and trim relay on my 2012 Etec. Has anyone done this on this model(E25DTSLINC)? Any advice is appreciated!
  4. P

    1964 Merc 60 6HP

    I was gifted this fine outboard and replaced the impeller and housing etc. The bottom of the water inlet tube appears to have had an "O" ring that is missing. I'm thinking it would seal the sleeve from the water pump housing when I reconnect the lower unit. Any Thoughts? Thanks Paul
  5. P

    Mercury 60 6HP lower unit

    Any good advice on getting the lower unit lined up with the powerhead? I seem to have difficulty lining up the splines on the main shaft to the powerhead, and don't want to use any force. Thanks
  6. P

    Evinrude Etec 25 HP E25DTSlINC

    I have a 2012 Evinrude Etec 25 HP. Was there a change in part numbers for the thermostat,cooling pressure relief valve, or water pump assembly? I want to service the engine and read on E nation that there were some issues with the original parts . Thanks!
  7. P

    New spark plugs 15HP Evinrude

    Do I have to check the gap on new champion L77JC4 spark plugs for my Evinrude E15RCDE 15HP? If so what should the proper gap be? Thank You.
  8. P

    1999 Johnson 3.3 HP J3REEC cooling system

    Besides the water pump assembly are there any other components to replace to clear the cooling system. I am not getting water coming out of the indicator. This motor has been used in salt water. Thanks Paul
  9. P

    1986 E15 RCDE Head removal

    "I would like to remove the cy "I would like to remove the cylinder head on this motor so I can attach the cover latch bolt assembly properly, as it is very difficult to attach since I replaced the thermostat,gasket and thermostat cover. Do I need more than a new head gasket to complete this...
  10. P

    Evinrude 15 hp cowl latch bolt

    "Anyone know how to get this b "Anyone know how to get this back on after doing a new thermostat on a E15RCDE. Tried every angle can't sem to get it reconnected with out taking the thermostat cover off, which then makes it near impossible to get thermostat cover back on???? Thanks Paul"
  11. P

    E15RCDE latch cover bolt

    Just completed new thermostat Just completed new thermostat install. struggling to reattach bolt and latch that holds cover down. Anyone know any tricks to get this done. PS water shooting out nice out of indicator hole now. Paul
  12. P

    Evinrude E15RCDE Thermostat Gasket

    "Installing new thermostat, Th "Installing new thermostat, Thermostat cover looks like there was only one gasket between thermostat cover and head, but two new gaskets came in package. Should I use one or two before I put cover back on? Really tight fit between thermostat cover and top of bolt...
  13. P

    1986 evinrude E15rcde Thermostat

    New water pump installed but w New water pump installed but water not shooting fast out of hole.Where is thermostat?
  14. P

    E15RCD broken bolt 1986

    "While doing a new waterpump i "While doing a new waterpump install and loosening the six bolts that connect the lower unit to the exhaust housing, one bolt snapped level with the housing nothing to grip at all. Any suggestions how to get the rest of this bolt out, they all appear to be...
  15. P

    86 evinrude 15hp water pump

    Just about to do my first wate Just about to do my first water pump removal and install any do's and do not's! I have a long shaft model. Thanks
See more
Back
Top