Logo
FULL SITE MENU

Recent content by 43_lx_merc_1996

  1. 4

    Please Identify this trim pump for a 1995 Mariner 90

    Never mind! All good, I figured it out. Thank you all for your assistance on this one! Cheers!
  2. 4

    Please Identify this trim pump for a 1995 Mariner 90

    Again, it’s not possible to fit that motor and reservoir the my round base with a round o-ring. I cannot seem to find a part number to change the base to fit the newer square reservoir. Again see my picture below.
  3. 4

    Please Identify this trim pump for a 1995 Mariner 90

    That motor is not compatible. See photos at the top. I need the round O ring setup, not square. I get that I need to upgrade the relays and change to a two wire. I’m still stuck. Thanks!
  4. 4

    Please Identify this trim pump for a 1995 Mariner 90

    What I really need is the matching pump motor, with the squared off edges
  5. 4

    Please Identify this trim pump for a 1995 Mariner 90

    Thank you, but Unfortunately all of those links refer to the following part numbers, all of which have the square seal. 8M0171817, 0G360002, & 824052. I have purchased two of the above parts and will need to return them. The round seal unit only seems to exist on the parts diagram. What am I...
  6. 4

    Please Identify this trim pump for a 1995 Mariner 90

    Engine serial number for reference
  7. 4

    Please Identify this trim pump for a 1995 Mariner 90

    Hello all. I’ve been struggling for months trying to find a replacement power trim pump for my 1995 90hp 2-Stroke Mariner project. All part numbers that I have located via Merc and aftermarket refer me to various trim pumps with the square gasket, whereas mine is a round gasket/O-Ring. See below...
  8. 4

    starboard engine stalls when hot at slow cruise.

    Hello, Just started getting an issue of my starboard engine stalling out at a slow cruise when hot, will not re-start until completely cold. The strange part is when I turn it over while my port engine is running, it seems as though a load goes onto the port engine and almost stalls that one...
  9. 4

    Re-Torque Intake Manifold - AQ260 350 V8

    Just looking for an opinon on if it is ok to Re-Torque the Intake Manifold on an AQ260 350 V8? This season, it has developed a slow coolant leak near one of the bolts which ends up burning and creating a pretty nasty smell. I just have one, maybe two small trips left for this season and won't...
  10. 4

    1988 9.9 stalling when hot.

    I have a 1988 9.9 that stalls when hot. If I pull the choke out briefly, before it stalls the engine will continue running. After a few minutes I can push the choke back in and it's just fine. This problem usually happens after running at a high RPM for a few minutes, then slowing to half...
  11. 4

    9.9 running on one cylinder

    My 1988 9.9 is running on one cylinder. I have replaced both coils and both plugs... Still have the same problem. Ideas? any help appreciated! thanks Chris
  12. 4

    Replacing exhaust manifold

    I'm about to replace one of my exhaust manifolds on an old AQ260 V8. Any tips on how to not break any bolts etc? Should I do it when the engine is warm? thanks Chris
  13. 4

    Engine sitting for 6 years

    I'm looking at a boat on Sunday that has an engine that hasn't been run in 5 years. Are there any quick checks to do, other than fully servicing it to get it running? much appreciated Chris
  14. 4

    6 hp revs up slowly

    My 1976 6hp revs up slower than it has in many years. Starts and runs great otherwise. Any ideas appreciated! Thanks Chris
  15. 4

    Distributor part number?

    I'm trying to match up an electronic ignition for my aq260 without much luck. The number stamped on the side of the distributor is 11114878H6. Doesn't seem to cross reference to any Volvo or Sierra part numbers. Any ideas? Thanks Chris
See more
Back
Top