Logo
FULL SITE MENU

Search results

  1. B

    Hard to get into reverse

    Hello. I have a mercruiser 1.7 engine with alpha one gen 2 drive. Last year I changed gimbal etc.. If I go from forward to neutral, it goes well. If I go from reverse to neutral, it can be a little difficult to get it in neutral, I almost have to put the gear lever forward. What do you think...
  2. B

    What is L and R on the alternator?

    Hello. I have Mercruiser 1.7 DTI with alternator that have L and R terminals. L is for the charging light on dashboard. But what is R doing? Does R output the same power as B+ ? Wire scheme is attached.
  3. B

    Installed gimbal bearing. What bolt to block the grease line?

    Hello. I have installed a new gimbal bearing (grease-free). So now I have to block the grease line. Anyone knows what bolt will fit?
  4. B

    Winterize Mercruiser 1,7?

    Hello. I was wondering how you fill coolant in the sterndrive and engine before storing away for the winter. Cummins mercruiser 1,7 diesel with alpha one gen 2. - Change oil in the sterndrive. - Connect garden hose to the sterndrive and clean the system with fresh water while engine is running...
  5. B

    New tachometer. Still showing 0 rpm

    Thank you for your answer o2batsea, that will be my next step if this doesnt work. Changed part 22 today (see first post for drawing) without no luck. Removed the tach module and opened it. Anyone can make this board? :)
  6. B

    Mercruiser Alpha One Gen 2 trim adjustment

    Opened up the puck and cleaned it. It was too much grease in there. Anyway. Does this seem right? Pictures showing all way down and all way up to limit (trim limit 52mm alpa one gen 2).
  7. B

    Mercruiser Alpha One Gen 2 trim adjustment

    Thank u. Can this be done when it is on water? Or would water come inside the pucks when loosening them?
  8. B

    Mercruiser Alpha One Gen 2 trim adjustment

    Hi. I need to adjust my trim sender to match the gauge and the trim limit. What should be the upper limit? I have read 20 3/4" and 21 3/4". Alpha One Gen 2 on a 2006 boat with mercruiser 1.7 DTI engine.
  9. B

    New tachometer. Still showing 0 rpm

    Hey there. A few months ago I turned the battery polarities wrong way, started up the engine and the cable from the alternator to the battery burned up. I changed the cable and noticed the tilt monitor and tachometer was dead. Anyway. Now I have changed the tachometer to a new one, just like...
  10. B

    When did Mercruiser 1.7 get the upgrade?

    Hi. When did mercruiser 1.7 dti get the update? Better wastegate and turbo etc.
  11. B

    Troubleshot tachometer?

    Hi. Is there a way to troubleshot the tachometer and trimindicator somehow? Mercruiser 1.7 dti.
  12. B

    Installed batteri polarity the wrong way

    What do u think? Those marked red are burned. But I cant figure out where they connect alltogether in the wire harness. I have removed the blue cable from 50amp fuse, start relay, starter and dynamo. Now I think nothing is connected that could cause shorting. I will install a new 4mm2 cable...
  13. B

    Installed batteri polarity the wrong way

    Have to check tomorrow if more wires are fried. I hope only the wire marked in red is the one that is fried. But I cant remember that this blue wire goes to the circuit breaker. It look like it goes straight to the wire harness to the front of the boat.
  14. B

    Installed batteri polarity the wrong way

    So I did it. Connected + to - and vice versa, started the engine and I saw white smoke in the engine compartment. Shut it off. I have been driving it on the ocean a couple of times. Engine: Mercruiser 1.7 sterndrive (boat from 2006) BUT. Today I noticed this: It became dust when I touched it...
  15. B

    Mercruiser 1.7 engine anodes location?

    Hi all. Where are all the four engine anodes on mercruiser 1.7 located? I can only find three🤔
  16. B

    Mercruiser 1.7 dti: How much engine oil and coolant?

    Hi. How much engine oil and coolant goes into Mercruiser 1.7 dti? (Apha one gen 2 sterndrive). Boat is from 2006. I managed to pump out 4 litre, but shouldnt it be like 6.5 litre?
  17. B

    Alpha One Gen 2: Exhaust bellow came loose. How should it be mounted?

    Hi there. I just replaced the gimbal bearing and all bellows. I tilted up the engine and the exhaust bellow came loose. Look at the picture. Where is the metal clam supposed to be. On the top?
  18. B

    The shield around wastegate/turbo

    Hi. Anyone know the part number or name of the silver shield wrapped around turbo&wastegate? mercruiser 1,7 dti.
  19. B

    Remove shift cable? Mercruiser 1.7 Alpha one gen two

    Hello. I am changing bellows on my alpha one gen two. The boat is produced in 2006. But how the heck do I remove the shift cable??
  20. B

    Complete impeller and bellow kit for my Mercruiser 1.7 alpha one gen two

    Hello. I have noticed that impeller and bellow kit are cheaper on ebay and Amazon than in my country. I also noticed the kits are different even if they are for the same engine, I have never opened my engine before so I dont know what I need. I have a Mercruiser 1.7 dti alpha one gen two engine...
Back
Top