If Can anybody send me a picture of a QUICKSILVER BLACK DIAMOND PROP / 12 1/2" x 8" ????
I was using a 12 1/4" x 9" prop and that one hand rounded edges all around each blade. (No noise)!
Now I put on the same prop except it's a 12 1/2" x 8".....
Now I have a "singing propeller" between 1000rpm...
Looking for a 2000-2005 MERCURY 60hp BIGFOOT.
2 stroke or 4....
Close to Holland Michigan would help!��
I'm looking for good running!!! (Not "it needs work first)!
Thanks!
I have a 21ft SunTracker pontoon.
if you have a MERCURY 60hp BIGFOOT....
does it work well for your pontoons weight and size
without "any" prop blowout at any speed??
im looking to buy a 2000-2005 MERCURY 60 BIGFOOT.
I have a 2002 MERCURY 40 hp / 2 stroke on my pontoon.
The current 40 hp is a long shaft. (20")
It's mounted as low as it can go. It blows out at w.o.t on calm
water. I'd like to switch to a 2002 MERCURY 60 hp /BIGFOOT / 2 stroke!
The Lake we fish is 7 miles long and has frequent waves of 2ft...
Ok.... I get prop blow out at w.o.t is reached
at 5500 rpm's with my 2002 MERCURY 40 hp.
I get it with 3 blade and 4 blade props. I get
it with motor pod and engine lowered 1" with
spacers. It does it with SE SPORTS 200 hydrofoil
added.the motor is mounted as low as possible.
my thinking is the...
Need a certain prop set-up if anyone makes what I need!
For : 2002 MERCURY 40 hp. / 13 spline / 12 1/2" x 8" x FOUR BLADE. / No cupping!
"THANKS FOR ANY HELP"!!😳
I've got a 21 ft.Suntracker pontoon with a 12 1/2" x 9" three
blade prop. Rpm's are 5500(perfect) SPEED 16mph (perfect)
the "top" of the prop blades are 1" below the bottoms of the
pontoons. And I still get prop blow out at wide open throttle.
the engine is as low as it can go. I lowered the...
I have a 2002 Sun Tracker 21 ft. Pontoon w/ MERCURY 40hp.
2-stroke. Two cylinder. I have a MERCURY Black Max prop
that is 12 1/2" X 9" (3 blade).....the top of the blades are the
same height as the bottom of the two toons.
I only get 4900 rpm's and 13 mph....and when it hits 4900 rpm
the prop...
Which burns hotter and cleaner...87 octane w/ 10% Ethanol,...
or 90 octane that is Ethanol Free?
Ussually higher octane burns slower, and not as hot as a lower
octane,...but I see on the internet that in this case, the Ethanol
Free would burn cleaner and somewhat hotter and with better
gas...
I have a 2002 mercury 40hp (0T571672)
With motor Off....
Forward....prop turns engine hard one way and clicks the other.
Nuetral....prop spins freely both ways, smooth as silk....
Reverse....prop turns engine hard both ways!
(is that right for reverse? If it is how come??)
I have a 2002 Mercury 40hp...2 stroke...two cylinder.
it has a slower than rpm knocking sound when put into
forward or reverse. NOT in nuetral...NOT when prop is off...
NOT when rpm is bumped up 300 rpm.
(the prop spins free and no sound in Nuetral)
(In Forward, the prop clicks on the dogs one...
If anyone has a 2002 Mercury 40hp / 2 stroke / 2 cylinder
one carberator....can you take a one picture of the "linkage
rod between the shifting arm and the throttle cam"!
(IF YOU HAVE REMOTE CONTROL...not tiller.)
(not any pictures out of service manuals. I already have one).
Take the picture...
If anyone owns a 2002 Mercury 40 hp/ 2 cylinder
"one carberator"/ 2 stroke.....
IDLING IN FORWARD GEAR IN WATER OR GARBAGE CAN!??
I'm interested in the sound of it. (Compared to mine.)
if so, send a clip to me at [email protected]
Thank You!
Has anybody used the FLO TORQ REFLEX HUB KIT with
any prop specifically to tone down a noise issue like prop
rattle or any other sound? AND HAD SOME SUCCESS??
(that's what it was designed for anyway).🤔