Logo
FULL SITE MENU

Recent content by Bevo2000

  1. B

    1994 Force 40hp Idle Speed Adjustment

    Thank you Jerry. I think it's the cable in the attached photo.
  2. B

    1994 Force 40hp Idle Speed Adjustment

    Hi Jerry, I need a little bit more help. I disconnected the throttle linkage but that didn't do anything to close the gap of the idle speed screw. Could you tell me where the trunion is or what it looks like?
  3. B

    1994 Force 40hp - How to check timing?

    Motor: 1994 Force 40hp (serial # 0E067660) I have a service manual but it does not have any information about checking if the timing is correct. Could someone please help point me to the right resource as I am sure this question has been asked before. FYI -- I did search the Force motor forum...
  4. B

    1994 Force 40hp What is this hose?

    Motor: 1994 Force 40hp (serial # 0E067660) Please let me know what this hose in the picture is for? I goes from the starboard side all the way to the port side and then hidden behind a bunch of electrical stuff. I wanted to replace it because it has some cracks but I didn't want to mess up...
  5. B

    1994 Force 40hp Idle Speed Adjustment

    Motor: 1994 Force 40hp (serial # 0E067660) I bought the service manual jerryjerry recommended and am trying to adjust the idle speed. The idle is high so I turned the screw counter clockwise to lower it. However, it has no effect because the linkage on top is holding it in place (please see...
  6. B

    1996 Evinrude 60 hp - Why won’t it start?

    Please help me troubleshoot this. I recently picked up a non-running 1996 Evinrude 60 hp and am trying to bring it back to life. I have done the following: 1) Replaced water pump 2) Clean carb twice to make sure 3) New spark plugs and spark jumped a gap of 1/2” 4) Compression is between 135...
  7. B

    1994 Force 40hp Impeller Replacement HELP !!!

    Hello Pros, I inherited this motor, but unfortunately the water pump assembly was ALREADY removed when I got it and I am trying to put it back the way it was supposed to be. I am stuck at this point because: 1) I cannot slide the drive shaft down far enough for the pin to lock against the...
  8. B

    Cam follower adjustment for 1991 Johnson 25 HP (J25TELEI)

    I need help with adjusting the cam follower to sit between the two marks on the cam. Below is a picture of the instructions from the service manual. However, that procedure only allow the cam follower to touch the cam (or not). I can't move the cam follower back and forth to sit between the two...
  9. B

    Is this a bad fuel pump for sure? 1991 Johnson 25 HP (J25TELEI)

    Hi all, I have been suspecting that the fuel pump is bad. Please watch the video below showing my motor running. https://youtu.be/k5HAxkuvYQQ
  10. B

    1991 Johnson 25 HP (J25TELEI) Fuel Issue

    Hi all, I recently bought this motor and am currently troubleshooting a difficult start/idle issue. I have noticed that gasoline is pooled under the carb and don't think this is normal. If this is not normal, what is the likely cause of this? Thanks.
  11. B

    1974 Johnson 25hp [25RL74M] Throttle Adjustment

    Hello everyone, I have searched everywhere but unable to find a step-by-step guide to set the carb throttle to original factory specs for my motor (1974 Johnson 25hp [25RL74M]). After installing the Ignition Tune-Up Kit (0172523) and the Carburetor Kit (0396701), I thought this was a piece of...
See more
Back
Top