Logo
FULL SITE MENU

Search results

  1. yzf125

    Evinrude 3 HP Coil Sensor Install ?

    Hey guys, I have to replace the coil sensor under the flywheel, There are several lines on the coil sensor bolt hole location and one large line on the motor where it screws down. How do I know where this should be adjusted to ?
  2. yzf125

    No spark 1999 Johnson 3.3

    Hey guys, I have no spark on this 1999 Johnson 3.3. How do I test these ignition parts #6 and #8 ??
  3. yzf125

    75hp Mercury ELPTO lower unit Oil ?

    Hey guys I am going to change my lower unit oil in my 2002 Mercury 75hp 2 stroke ELPTO and was wondering what "weight " oil I should be using. I don't remember if I used 80 or 90 the last time I did it. I see some lower unit oils that say 80/90 some just 80 and some just 90. What should I be...
  4. yzf125

    2002 Mercury 75 hp ELPTO Main Jet Question

    Hey guys, I am just wondering why Mercury put a smaller size jet in the top carburetor and same size for mid and bottom on my 2002 Mercury 75 hp ELPTO ?? The parts chart shows this also and I just want to know the reasoning behind this. Just doesnt make sense to me :confused: .052 - Top .054...
  5. yzf125

    Main engine fuse blown while sitting ?

    Hey guys, My boat has been stored in the garage for the winter, it has a 2002 Mercury 75hp ELPTO. I have done nothing but charge the batteries every month, I went to raise the motor the other day and nothing worked so I checked the fuse on the motor and noticed the Main engine fuse "20 amp" had...
  6. yzf125

    Many different carburetor models whats the main difference ???

    Hey guys I have a question about all the different cab models For my 2002 75hp # 0T564442 ELPTO. First off, why is there 5 different carbs for my engine model year, and what are the differences, The only thing I can think of is the Main Jets ?? It shows 5 different 75hp model carbs WME-82...
  7. yzf125

    Rev limiter is where ?

    Just wondering what internal component the rev limiter is located in on my 02 Merc 75hp elpto. I see on older models its an individual external unit, but mine doesnt have that. Must be internally in the CDM modules ?
  8. yzf125

    What would cause this ??

    Hey guys, What would cause these wires going to the voltage regulator to melt together ?? and would this cause any issues other than the charging circuit ?? ( Motor is in my sig ) I ask because I still have an ongoing problem with anything past 4k I get what feels like a rev limiter kicking...
  9. yzf125

    Supposed to do this ??

    Hey guys, I was chasing an ongoing problem with my motor and decided to throw some parts at it instead of spending the big bucks at the stealership 100 per hour !!!! So I proceeded to replace my trigger on my 75hp mercury, When I was removing the screws that hold the stator to the motor each one...
  10. yzf125

    Question with Timing

    Hey guys, I wanted to check timing on my 02 Mercury 75hp 2 stroke. Now the sticker on the side of the motor says " 2 BTDC / 18 BTDC " I am assuming this is @ cranking settings ? So I checked and came up with Idle cranking at 5 and WOT at 20, Is this ok ? [/URL][/IMG]
  11. yzf125

    How to test a CDM ignition module ?

    Hey guys, I am having an issue that Im starting to think could be ignition related and would like to know how to test a CDM module (coil pack) on my 2002 Mercury 75hp. It may be cutting in and out after half throttle that I am noticing, originally thought it was fuel related but I have done...
  12. yzf125

    2002 Mercury 75hp WOT surge

    Hey guys, I have an issue with my 2002 Mercury 75hp elpto. When wide open throttle it just seems to fall flat and surges a bit, If I back off to about 3/4 or 1/2 it seems fine. Runs good out of the hole, I can just mash it and it takes right off with NO hesitation, Its only WOT that I have any...
Back
Top