Logo
FULL SITE MENU

Search results

  1. B

    Oil/Fuel ratio for a 18602(c)

    Im pretty sure its 50 but I will be running it hard and I want to make sure. Thanks
  2. B

    6520 ignition

    7520,my mistakeLooks like the condenser wires have melted some and I may have routed the wires too high and too close to the flywheel. What concerns me is that it looks like the coil wires have begun to melt also,Id like your thoughts. Id rather spend the 60 bucks for new coils than row my boat...
  3. B

    18602 spark plug gap

    Can someone give me the proper gap on these please? Fouled mine with WAY to much oil. Thanks
  4. B

    Impeller for a 15014

    Cant remember how I found the right one,probably here. Can I have some help with a part number please? Thanks
  5. B

    Need to check my pressure tank for leak

    7520,cruise-a-day tank. Orings recently replaced ,and diaphragm and main gasket replaced in recent years. I thought that maybe the tank had pushed out a little fuel while fishing,but Im not sure if it was water from getting fish in the boat,I netted quite a few back there.Hard to tell by smell...
  6. B

    66 rude 18hp

    Seemed a little hot,Impeller is new,replaced both grommets on water tube after LU reseal. How long should I be able to hold my hand on the head? I ran it hard for 8.5 miles with a 20 min break which was enough time for it to cool to the touch. Then ran it the 8.5 miles back with no issues other...
  7. B

    67 6hp rude

    When I go from a trolling speed directly to wot she dies,choke to restart warm. If I throttle up slowly she runs fine throughout the range.Any insight would be appreciated. Thanks-B
  8. B

    Tuning low speed on a 1967 6hp

    I have replaced the ignition excluding the coils. Spark jumps a 1/4" gap nicely with a good snap. I have completely disassembled the carb and cleaned thoroughly paying close attention to the orfices and low speed circuit. I can not get it to run smoothly at a very low idle. I started with the...
  9. B

    1967 6 hp evinrude

    Does anybody know the thread pattern for the throttle shaft butterfly screw? Lost it,I will order one but I want to see if the hardware store has one in the gun screw hardware bin. Thanks-B
  10. B

    6HP

    Man I had a heck of a time getting the lower to mate back up with the power head,dont quite know why. I could look up inside the exaust housing and see the slot for the pin and the bottom of the seal assembly,but could not get it in all the way.Finally it just went in easy.Matbe the drive shaft...
  11. B

    High speed jet removal

    I'm working on a 1967 6HP still,do I need a special tool to remove the high speed orfice in the carby? I don't want to booger it and I will purchase the tool if needed. Thank you-B
  12. B

    Part numbers

    Would you guys give me the part numbers for the carb kit w/float and the lower unit seal kit please. I am working on a 6702D. A 1967 6HP Evinrude. I'm refurbing it for a friend.Thank you-B
  13. B

    1967 6HP Carb question/LU question

    6702D Got the Ignition dialed in and tanked it,timing light says it perfect on the first mark both cylinders. New points wires condensers plugs. In order to hold a low idle and stay running I need to close the choke a little bit. Once I idle down and the sucking sound starts that's when I have...
  14. B

    1967 6HP Rude manual starter

    I replaced the rope as described in the service manual by putting a pair of pliers under the pinion to hold it in the up position while replacing the rope. When I secured the new rope the starter assembly recoiled the rope once and the second time I pulled on it ,it would not retract. Can I...
  15. B

    Stuck flywheel

    6HP Evinrude 6702D.I have never had a stubborn one like this. It is under tension from the puller and I have sprayed penetrating oil on the crankshaft. I tried rapping on the puller center bolt. I will check later to see if it has popped and tighten a touch more. Is this the proper course of...
  16. B

    Model ID

    Cross posted. Got a Rude 6HP in the shop and need some parts for a refurb. Transom bracket is donated from another motor.The freeze plug on the powerhead says 6702D-E01598. Need some help on this one. Thanks-B
  17. B

    Model ID

    Got a rude in the shop and need some parts.Transom bracket is donated from a 5302 which is a '63 5.5 I think.Model number on the freeze plug on the powerhead says 6702D-E01598. Can yall help?Thanks-Blair
  18. B

    18602 starter recoil assembly

    I had my recoil assembly come apart on me this weekend.The capture nut came off at some point and the recoil hold down bolt did a dance with the crank and cracked the recoil housing. Not a good sound.Got a few more starts after using the back of an axe to reshape the housing and reassembling...
  19. B

    Spaghetti seal

    What is the part number for this stuff, I could use extra too. Thanks-B
  20. B

    15014 lower unit

    I have another post on this 15014 lower unit but I believe it has become confusing to the reader. I have this lower mated to a 18602. I noticed some screaming from the lower the last time out. Upon inspection the gears look fine but I noticed what could be scoring from the pinion on the lower...
Back
Top