Logo
FULL SITE MENU

Search results

  1. C

    1954 10 hp johnson

    i need to tighten the pivot friction and cant figure out how ther is no friction screw like on my 1956 7.5 hp johnson thanks clay
  2. C

    1954 johnson 3 hp jw-10

    hello when setting the points should i set the gap when the crank key is centered on the point spreader or when the letter o in the word top on lob roller is centered on the point spreader thank you clay
  3. C

    1954 QD 15 10 hp johnson

    motor is still running rough checked inside re-built carb 3 times checked re-buit ignition 3 times. im noticeing black wet gunked up plugs is it possible that the head gasket is leaking water into the spark plugs making it run rough
  4. C

    1954 qd-15 tune up problem

    the motor starts easy but i cant get the idle set it goes pretty low. but i can screw the low speed needle all the way in closed and it does not change the motor i rebuilt the carb new coils points plugs i can spray carb cleaner at the packing nuts and they seem sealed
  5. C

    1954 10 hp johnson top crank seal

    hello i was getting a lot of gunk on my ignition plate and points and coils so i diassembled everything under the plate on the top of the crank the last things there were pieces of an o-ring and pieces of a plastic ring about a quarter of an inch thick about the size of a quarter, probably if i...
  6. C

    1954 3hp jw 10

    does any body know the sierra part# for the lower unit seal ki thank you
  7. C

    1954 10 hp johnson

    hello i replaced coils, points, wires carb kit, plugs,converted to a fuel pump,new fuel lines all in the last week, i can get the motor to start but it runs very rough.i did the 1 and 1ahalf turns on the needle valves to start to set carb and nothing works i have tore it apart and checked...
  8. C

    1970 9.5 hp carb

    hello im rebuilding my 1970 9.5 hp carb and i noticed that on the carb body just to the left of the low speed adjustment needle there is a small hole in the casting i think there is supposed to be like a little lead shot bee bee that is supposed to be there and it is gone can i just plug this...
  9. C

    1970 18 hp johnson fuel pump

    hello i replaced the fuel pump hello i replaced the fuel pump on this motor and the motor wont run unless i keep priming it with the bulb is it possible that im not getting a pulse from the motor any more to run the diaphram pump
  10. C

    1970 95 hp evinrude water pump removel

    hello i bought the motor so i hello i bought the motor so i need to change the impellor do i need to pull the power head like on my older johnsons or not thank you
  11. C

    1977 175 hp johnson carb question

    hello i have a V-6 1977 175 hp hello i have a V-6 1977 175 hp johnson with three carbs that i bought cheap the top carb does not have a choke butterfly only the middle and bottom carb have butterflies is this correct or did the prior owner mess with this thank you clay
  12. C

    90 hp shift rod oring removeal

    hello i need to replace the sh hello i need to replace the shift rod o-ring but i cant drive the brass bushing out of the houseing i have a tapered rod i use on smaller motors to drive the bushing out but it wont budge and im afraid im going to damage the houseing any sugestions thank you clay
  13. C

    90 hp johnson timing

    hello i got finished with my r hello i got finished with my rebuild today thanks to all of you that helped me/ a few more quick questions. rebuilding this motor should have not changed my timing should it. i made sure that the advancement linkage adjustment did not get disturbed when i tooked...
  14. C

    Installing standard fuel

    hello im getting rid of my VRO hello im getting rid of my VRO i bought a standard fuel pump i see the mounting holes on my intake for it there are to screw holes and a port in the middle of them that is pluged how do you get that plug out so i have vacume and pressure to the pump does it screw...
  15. C

    Bolt torque specs

    "hello i have the torque specs "hello i have the torque specs. from my johnson service manual, but there is a torque ranges on some bolts for example lower crankcase bolts 96-120 in. what should you do go to the minimum,mid-range or max. your input is very welcome thank you clay"
  16. C

    Installing crankcase head on to crankshaft

    hello im just put a new seal a hello im just put a new seal and o-rings on my crankcase head and i need to bolt this on to the crankshaft it has four bolts holes there is a fifth hole on the ring that is not threaded for a bolt do you position this hole to be by the little weep hole that...
  17. C

    1992 90 hp johnson setting timing

    hello i read somewhere that y hello i read somewhere that you can set your timing with out starting your outboard by using a spark tester and your throttle at wide open and turning the engine over what is this procedure and what kind of spark tester do you use i have never seen one thank you
  18. C

    1992 90 hp johnson vro

    hello can i install a standard hello can i install a standard 3 hose fuel instead of my vro is the pulse port nipple on my intake a pressure and vacume port that will run the standard fuel pump. i have already bypassed the oil side of my vro and have been mixing my own oil but know the vro pump...
  19. C

    1992 90 hp johnson crankshaft dowell pin

    "thank you guys for your respo "thank you guys for your responce, now that ive got the block back from the machine shop today the crankshaft dowell pin is there but it is either sheared off flush in the block or has been pushed down into the block, any ideas how to get it out so i can install a...
  20. C

    1992 90 hp johnson crankshaft installation question

    "hello im going to start to pu "hello im going to start to put my block back together after the bore job it got, does the bearing on the middle main crank journal, the one with the split sleeve and a groove and clip around it have to be rotated to a spot on the block. there is two holes on the...
Back
Top