Logo
FULL SITE MENU

Search results

  1. C

    Chrysler 440 exhaust manifold gaskets

    I used the green gaskets from Osco about 5 years ago on my exhaust system. I developed an exhaust leak. I found the exhaust maniflod gaskets had blown out the bottom of the manifold/head joint. I will be using header gaskets this time. I also noticed the gaskets on the risers had worn out. The...
  2. C

    wich intake manifold gaskets for chrysler 440 with heat riser blocker

    I can't find Chrysler 440 marine intake gaskets with heat riser blocker plates. Does anyone know where to find them?
  3. C

    Stalling 1977 Chrysler 440s

    Both engines have stalled, but the worst is the port side freshly rebuilt 440. The engine is perfect mechanical condition after total rebuild. I put new Mallory distributors and Edelbrock 1410 carbs on both motors. The starboard has stalled, but not as much. The engines start and idle...
  4. C

    My fuel tank replacement project from 2012.

    http://www.thehulltruth.com/boating-forum/343859-jersey-dawn-deck-fuel-tank-replacement-advice-watch-progress.html Great pics of the project. Ed
  5. C

    ground wire sparking? opinions?

    I have a 1977 Jersey Dawn 40' with twin chrysler 440's. There are 3 different wires that come down from the electric panel and ground to the engine block. I was taking them off for and engine rebuild and one of them sparked. The other 2 do nothing if touched to the block. I have no 12 volt items...
  6. C

    Chrysler circuit breaker (50 amp)-new number

    Chrysler part number 2875586 replaced by 4142032. It is the red button to reset the electronic ignition. Google this number to find it. :cool:
  7. C

    Need chrysler 440 marine long block or short block

    My port standard rotation engine has a groove in the cylinder #7. It is a single groove about 1/16" deep that stops about 2" short of the top of the cylinder wall. I pressure tested at 100 PSI before I pulled the heads today. I don't know if it can be rebuilt or not. Now I am thinking maybe I...
  8. C

    Distributor help for chrysler 440 marine engine reverse rotation

    I am trying to replace the distributors on both my standard and reverse rotation engines. The springs inside are rusty and I don't trust that they are working correctly. I am currently working on my starboard (reverse rotation) engine and have not touched the port engine yet. I just had the...
  9. C

    Chrysler 440 timing advance curve

    I know that we could not find a factory official timing curve for the 440. This should get the job done. I purchased a new distributor for my standard rotation 440 and am rebuilding my distributor for my counter-rotation 440. I called tech-support to get the timing curve from the new...
  10. C

    I need chrysler 440 heads-casting 4006452-help

    Hello, I am looking for a set of chrysler 440 heads with casting number 4006452. I will have them rebuilt. My e-mail is [email protected] (my name is Ed). I had a miss in the engine. Upon checking..... I had no compression on #4 cylinder (reverse rotation motor). The center of the spark...
  11. C

    Putting 1410's on my 440's-PCV Question

    Okay, I am putting Edelbroch 1410 carbs on my Chrysler 440's this weekend. I read about drilling out the carbs and threading them for a hose barb to hook up the pcv valve. I am nervouse about drilling them. My Chryslers have 8* wedges(plastic). I was thinking about drilling and taping them...
  12. C

    Westerbeke 7.0BCGC-speed surging-possible E-10 gas problem?

    My generator has not been started for 2 years. It was properly winterized and fogged before storage. I had to replace my fuel tanks due to ethanol 10% fuel. I have brand new tanks and a-1 rated fuel lines. The generator ran great on non-ethanol fuel before it was stored. After repeated...
  13. C

    9.9 hp nissan outboard-paint pealing off

    I have an older 9.9 hp Nissan outboard that is sitting in my garage. The blue paint is pealing off it everywhere. The uncovered aluminum looks like it has white powder on it. Like a corroded battery terminal. I hosed it of with fresh water and it continues to corrode and peal. Any ideas of what...
  14. C

    7.0BCGC genset surging after e-10 fuel switchover???

    My generator has not been started for 2 years. It was properly winterized and fogged before storage. I had to replace my fuel tanks due to ethanol 10% fuel. I have brand new tanks and a-1 rated fuel lines. The generator ran great on non-ethanol fuel before it was stored. After repeated...
  15. C

    Chrysler 440M intake maniflod advice needed

    Hello, I am considering putting an Edelbroch performer (2191) aluminum intake on my chrysler 440M (year 1976). I have the single sided raw water pump on the engine. I beleive it is called a half system. Antifreeze runs through the block and raw water through the exhaust manifolds. Is this a...
  16. C

    Battery/ground wiring question.

    I have a 1977 Jersey Dawn with twin 440 chrysler inboards and a westerbeke 8kw generator. The generator has its own battery as does each 440 inboard. There is a set of wires tapped off of the port side 440 starting battery that feeds the electric panel on the flybridge. I have something...
  17. C

    choosing type of plywood for glassed over deck...advice.

    I am replacing the fiberglass fuel tanks in my 1977 Jersey Dawn 40 sportfish due to "evil-nol". The rear deck must come out and be replaced. My deck is currently 3/4"ply with 1/4" teak planks that have been glassed over. The total thickness is approximately 1". I am not a boat builder, but...
  18. C

    15 HP 2007 Mercury outboard wonbt idle

    "Hello, I am trying to help "Hello, I am trying to help a friend fix her new 2007 15HP four stroke outboard. She said it died at running speed and would not start. I started it up after getting towed back in (next day). It started easily and seemed to run fine,but won't idle. It just...
  19. C

    Raw water pump rebuildhelp

    "I am trying to rebuild a jabs "I am trying to rebuild a jabsco 18940-0010 raw water pump. It is the same as aSherwood g-5 or g-7B pump. I can't get the pulley off! I removed the roll pijn and set screw. The pulley does not want to come off. I tried a hub puller,but the pulley started to bend...
  20. C

    Chrysler 360 need manual

    Does anyone have a link to a f Does anyone have a link to a free download for a Chrysler 360 engine manual?
Back
Top