Logo
FULL SITE MENU

Search results

  1. B

    85/125 Lower units

    Have a cracked lower unit on a 1989 85hp Force. Motor wouldn't shift out of forward. I have found a 1988 Force 125, can I swap the lower units? Should that fix the shifting problem? Also when i read about replacing the water pump it said I need a special tool to install the seal. If that...
  2. B

    neutral lock out

    1989 85 Force. The key will not start engine unless the neutral lever on the '89 bayliner is in just the right spot. This is getting harder and harder to find. Is there an adjustment somewhere?
  3. B

    Forgot to winterize

    My brother pulled the boat wit My brother pulled the boat with the 85 Force out of the water to store but forgot to run the gas out or treat the gas. Is there any way that I can make sure the fuel doesn't gum up the carbs over the winter?
  4. B

    Leaking fuel pump

    The fuel pump on my 1976 6hp J The fuel pump on my 1976 6hp Jn has started leaking. Do I have to spring for a whole new pump or is there a rebuild kit. Thanks
  5. B

    Coil cracks

    "I am doing the ignition on a "I am doing the ignition on a '55 10hp Johnson. When I pulled the flywheel and looked t the coils they looked fine. They are light green and must have been replaced at least once. When I removed the stator to replace the plug wires, I did notice a very slight...
  6. B

    Battery type

    I have an 1989 Force 85. The I have an 1989 Force 85. The battery is now toast. What type battery should I purchase as a replacement? Thanks. J.Allyn
  7. B

    Bolt size to pull flywheel

    I am pulling the flywheel on a I am pulling the flywheel on a '55 10hp Johnson. What size bolts do I get for the flywheel puller? None of the supplied bolts with the puller fit. Thanks J.Allyn
  8. B

    Carb Kit

    "When I order a Carb kit for m "When I order a Carb kit for my '55 10hp Johnson from here, does it come with the needles and seat or do I need to buy them separately. Also, can I buy just the impeller or do I need a whole kit if every thing else looks good. Thanks. J.Allyn"
  9. B

    Fuel connector

    I am getting ready to tear int I am getting ready to tear into my '55 10hp Johnson. When I look at the male connector on the engine the ends seem plugged. Should there be an opening in the ends of the air and fuel sides? Or is there a valve that opens when the line is connected. I don't want...
  10. B

    Spark plug

    "I have a question for my 55 1 "I have a question for my 55 10hp and 63 10hp Johnson's. What is the correct spark plug? I have seen Champion j6c, j4c, and j8c all listed. Which is it? Thanks guys this is a great forum."
  11. B

    Fuel filter

    I have a '63 10hp Johnson. I have a '63 10hp Johnson. The fuel screen in the glass bowl was pretty well clogged and deformed. I replaced it with an inline filter between the fuel pump and the carb. Within a week the filter started to leak and I had to remove it. Seems to have split at the...
  12. B

    White gunk

    I have a 1963 10hp Johnson. I I have a 1963 10hp Johnson. It runs well. I noticed after this last weekend that there was some white gunk like vaseline coming out of the side of the lower unit above the water line and below the power head. It appeared to be coming from a small plate on the...
  13. B

    Spark plugs 85 Force

    Our 1989 85hp Force is many ti Our 1989 85hp Force is many times a challenge to start. I bought new plugs this year and it helped for a few weeks. Last time I used it the plugs acted like they were fouled again. These are surface gap plugs! Can I replace with a regular plug to eliminate...
  14. B

    Spark plugs

    What are the correct plugs for What are the correct plugs for a 1963 QD - 24 10 hp Johnson? The book says J8C's but on these strings I have seen J4C's and J6C's mentioned. I purchased it with J6C's and want to replace. Thanks.
  15. B

    10 hp Johnson QD24

    "I have it up and running but "I have it up and running but have a couple of Questions. 1. The high and low speed knobs are missing, where can I find replacements? Without them I can still adjust the carb but it vibrates out of adjustment after running awhile. 2. How do I adjust the tension...
Back
Top