Logo
FULL SITE MENU

Search results

  1. L

    compression

    I have a 1977 70hp Evinrude three cylinder with 90 psi on each cylinder, is this a sign of needing a rebuild ?. it seems to be low to me.
  2. L

    1979 Johnson 70 hp hard starting in river

    I have a 1979 70 hp 3 cylinder that starts right up on muffs but is a bit cranky in the river. will back pressure cause this ? what should i look for? thank you for any advise.
  3. L

    Scratch in cylinder

    I have a 1978 85 hp Evinrude . I was inspecting it for rebuild , found a scratch below exhaust port in one cylinder, you can feel it with your finger nail but it doesn't catch. will honing it fix it or do i need to bore it? or will it matter below the exhaust port in the skirt area .?
  4. L

    Rpm evinrude 150

    What is the wot rpm of a 1979 150 hp evinrude?
  5. L

    1989 60 hp shuts down to 2500rpm

    good morning: i have a 1989 60 hp evinrude , model #E60ELCEA . i have changed the thermostat and the temp sensor. it still shuts down to 2500 rpm, i have checked temp of motor when it does this and it 150 degrees , and the water coming out of pisser is cool to the touch.could...
  6. L

    At witts end

    i have a 1979 70 hp Johnson (70el79) i have had trouble with reaching wot for awhile , found the trigger was missing on one cylinder. replaced it ! rebuilt carbs because of trash in tank, installed inline fuel filter and put in fresh fuel. went to try it out it hesitated for a minite and...
  7. L

    1979 70hp johnson (no spark on #2 cyl.)

    Gent's , I have a 70 hp.Johnson 1979 70EL79R , it has no spark on the #2 cyl. number 1 and 3 has great spark. it jumps 7/16 gap. I changed the coil and it does the same thing,changed the power pac and it does the same thing. I checked the stator with an ohm meter , I set meter to...
  8. L

    lower unit 1977 70 hp

    i have a 1977 evinrude 70 hp . i need to install water pump.i have removed all 6 bolts from lower unit and also screw from shift rod,lower unit will not budge. if it is stuck in bottom of crankshaft how do i get it apart.:confused:
  9. L

    want to swap blocks

    i have a 1979 100 hp evinrude "1009983s" needs to be rebuilt. i also have a 1978 85 hp evinrude 85899c that does not. i looked up the part numbers and everything tells me that the blocks will interchange with the mid section but the drive shaft numbers are different,does this mean that the...
  10. L

    cough 1978 150hp

    i have a 1978 150hp evinrude that runs fine but has a bad cough to it at idle , could it be carbs or hopefully not reeds?
  11. L

    powerpac ? 1979 70hp

    i went to the river today and my 1979 70hp johnson was only running on one cylinder.when i got home and checked it out it was running on all three.the only thing i found was one ignition coil is leaking.I am thinking power pac.what do you think?:confused:
  12. L

    1979 85hp power head

    will a power head from a 1979 85 johnson interchange with a 1976 85 johnson?
  13. L

    compression test 1986 90 hp

    i have a 1986 90 hp johnson outboard.i ran a compression test after warm up and came up with these results. left bank top 115 bottom 110, right bank top 120 bottom 105. i have always went with 15 lb difference rule , i'm sure that would apply here .correct me if i'm wrong. model # j90tlcdc...
  14. L

    shifting rod 1979 150 hp

    i have a 1979 evinrude 150 , can anyone tell me what higth it needs to be in order for it to go into both forward and reverse gear? i do not have the omc tool .
  15. L

    Need new block

    "i have a 200 hp johnson 1988, "i have a 200 hp johnson 1988, j200txcor. ineed a new block , what years blocks will interchange ?"
  16. L

    Rebuild kit

    "i am looking for a carb,rebui "i am looking for a carb,rebuild kit for a 1995 dt8c 8hp suzuki outboard.can't find one anywhere.please help ."
  17. L

    Blows inline fuse

    "i have a 1979 70hp johnson, & "i have a 1979 70hp johnson, (#70el79r) i have installed a new starter a new ignition switch a new solenoid,when i turn the key to start motor it blows fuse on top of motor.any thoughts?"
  18. L

    200 hp johnson j200txcor 1988

    "i have a 200 johnson,compress "i have a 200 johnson,compression 75- 80 on all cyl,it is running a 4 blade prop 14 1/4 by 19. it is on a 20ft seacraft offshore, it is having trouble reaching top speed. i noticed that cavation plate is 2" below bottom of boat. would this hurt or do i need to...
  19. L

    Flywheel

    "one of the magnets came out o "one of the magnets came out of my flywheel,1988 200hp johnson.how do i replace it? and will a flywheel off of a 1989 johnson 200hp fit it?"
  20. L

    Prop selection

    what is the formula for findin what is the formula for finding the right prop for a boat
Back
Top