Logo
FULL SITE MENU

Search results

  1. greasemonkey

    NICE NEW set of Manifolds 318 360

    http://www.ebay.com/itm/Chrysler-Marine-Exhaust-manifolds-318-340-360-NEW-PRIMED-PAINTED-/271113396652?hash=item3f1f9e21ac&item=271113396652&pt=Boat_Parts_Accessories_Gear&vxp=mtr Grease ALSO,Have some other FWC parts from a 318
  2. greasemonkey

    Locked up lm 318

    seems as thought the cylinder wall is getttin thin, was thinking about boring thw whole block but not sure how far I can go
  3. greasemonkey

    Vee Drive /Shaft knocking

    Is this time for a rebuild or does the tranny sound like this! http://www.youtube.com/user/captlazybone#p/u/0/rWi3HuAz7sw Done some research in the install manual and seems a rough running engine,low idle causes this gear rattle and should go away with an elevated idle.The new mount I put on...
  4. greasemonkey

    2001' 115 hp EFI 4 stroke

    Starts every time, idles fine till its warm then idles rough and stalls and hesitates when accelerated Gas is goood ,Drained the VST ,cleaned out water seperator and in line fuel filter at engine Found the inner lining of fuel hoses in the filter housing(clear rubber) I assume the...
  5. greasemonkey

    Intake Manifold Gaskets...

    Got the new intake manifold gaskets there is no metal plates for the center hole What do these plates do? And why does Napa and otherparts not have the plates Anybody have a clue?
  6. greasemonkey

    1978 LM318s 1000hrs

    "What should I be doing while "What should I be doing while I have this thing torn apart?Should I go ahead and take the intake off and inspect? What would yall do?Yep Im from the South!Check the valves? Timing Chain?"
  7. greasemonkey

    Friday night party

    "Decided to dig in and let er "Decided to dig in and let er rip,replacing the exhaust manny and mounts,clean it up a bit,looks like a tad bit off water in the #3 cyl. and 4 bolts came out easy but ole #7 got me just a bit right Jeff. Wonder if u guys got any suggestion as what I shoul do while...
  8. greasemonkey

    So its the bolt screwed into the flywheel

    that u use to time the motor o that u use to time the motor on the '78 lm318?Theres about 3 holes that look like marks!!
  9. greasemonkey

    Anyone ever trailered a 31 Silverton

    Bout to haul it out and was wo Bout to haul it out and was wondering if anyone had any ideas about adjustments or if they might have a pic of a trailer they use?
  10. greasemonkey

    Runs at idle with 4 plug wires removed 318

    "Lookin for some help and sugg "Lookin for some help and suggestions.I have a 318RH rotation starts and runs but not firing on all 8 to say the least.I have spark and new clean plugs and wires,seems that should cause the motor to run on 8.I wonder if the cam is worn and the valves arent...
  11. greasemonkey

    Got it runnin but spark is weak

    So I get it warmed up and Im o So I get it warmed up and Im only pullin 9 hgs of vac through the non pcv hose fitting and put it in gear and it'll spit and sputter and die .I pulled a total of 4 spark plug wires off and held them in my hand and engine ran at idle and plugs sparked on a tester...
  12. greasemonkey

    1980 318s 31 silverton need heelp

    "I have an issue on my starboa "I have an issue on my starboard reverse rotation motor. I just put a new timing chain on because when I would try to start it , it would spit up through the carb(Carter reman).I could set the timing ,clean the plugs and it would run for 20 minutes and then start...
Back
Top