Logo
FULL SITE MENU

Search results

  1. E

    73 merc 500 doesnt seem to run wide open

    " I have a '73 merc 500 on " I have a '73 merc 500 on a 18ft alum.fishing boat that has never seemed to really open up out on the water,I've never gotten tach to work on it got a new one recently but hav'nt gotten it on yet.Any ideas about problems? Taking carbs off to have re- built...
  2. E

    140 hp year and what do the letters mean

    " Hi everyone, I've just p " Hi everyone, I've just purchased a 140 hp evinrude motor, Model E140TRLCTE Serial No. J0285611, it has trim and tilt. Can anyone tell me what year that motor is and what the "TRLCTE" part of the model No. is? Also, can this engine be fitted with oil injection...
  3. E

    1977 Mercury ou board

    " The top end is rattling on t " The top end is rattling on the outside of the motor i think it is the key on the flywheel And i changed the lower unit oil and it was grey Does that sound right when i unsrew it it releases th pressure form inside Is $175 a good deal It has a new...
  4. E

    Correcting too much oil in b77 85HP Johnson

    " '77 85 HP Johnson starts " '77 85 HP Johnson starts great, but once up to speed abruptly looses power and stalls. Very difficult to start after this...runs very slowly. I'm sure of what I did to cause the problem. I filled the 12 gallon inboard fuel tank with 87 ocatne unleaded to...
  5. E

    1990 30 OMC cannot shut off power

    " I was out on the lake two da " I was out on the lake two days after replacing the alternator, I tried to shut off the motor but it continued to run. I had to pull the coil wire to shut it off. With the key in the "off" position, I still have power as if it is in the "on" position After a...
  6. E

    37 repower

    i have a 22ft citation with 3 i have a 22ft citation with 3.7l and mr outdrive i need to know if anyone knows if a 4.3 complete package with a alpha drive unit will drop in without any cutting of the transom and if the engine mounts would still be in the center of the beam like the 3.7
  7. E

    115 Mercury inline 6 problems

    " My 1986 115 seems to have on " My 1986 115 seems to have one cylinder that does not work when the engine is cold. After about 15 minutes or so you can feel the power gain or if its driven for a few minutes, shut off for 10 minutes and restarted, it runs good. Compression is 115-120 in all...
  8. E

    Still hard to steer

    i have an older chrysler ob i i have an older chrysler ob it was hard to steer with the wheel so i disconnected it at the motor it was still very hard to steer. I put new grease in it it loosened up some but is still hard to steer anyone know why or if there is a way to fix it thanks ERIC
  9. E

    What size motor is needed

    i have an older 21ft cuddy ca i have an older 21ft cuddy cab with a 60 hp chrysler ob what size engine should really be this size boat and how fast do you think the 60hp will go thanks eric
  10. E

    What prop to select

    i have a 1974-76 chrysler out i have a 1974-76 chrysler outboard 60 hp my prop was spun and i don't know a thing about them the prop is a 3 blade size is 11X13 can anyone tell me what i can do and where to get a new one i don't know a thing about pitch either please help thanks EF
  11. E

    ADJUSTING SHIFT CABLES

    I JUST PUT A CONTROL BOX AND I JUST PUT A CONTROL BOX AND CABLES ON A 1974-76 CHRYSLER 60HP THE MOTOR RUNS GREAT AND THE LUBE IN THE LOWER UNIT IS GREAT. TOOK BOAT OUT SAT. IT TROLLED THREW 6 MILE AN HOUR ZONE BUT WHEN I GAVE IT THROTTLE THE ENGINE REVED UP BUT I DID NOT GO ANYWHERE. WHAT COULD...
  12. E

    What control box can i use

    " i have a 1974-76 Chrysler 60 " i have a 1974-76 Chrysler 60 HP outboard but i have no control box what exactly should i look for . where i live there is a boat junk yard and they have plenty of older model controls but i need to know which one please help, trying to get boat in water by the...
  13. E

    How to pressure check lower unit

    i took off my lower unit but i took off my lower unit but i don't know where the water is getting in at. how do i check to tell what seals are bad or what i have to replace
  14. E

    Troubleshooting lower unit

    " i redrained lower unit, ther " i redrained lower unit, there's still a little bit of water in the fluid, the fluid was coffee color but i received no metal particals at all. what seals should i replace what gaskets should i replace the bearing and should i take the lower unit off to do this...
  15. E

    Need some ID help

    ok I bought a motor the selle ok I bought a motor the seller told me it was a 150hp mariner but it has 175 hp on the cover along with Blackmax ser#5316410 I would also like to know the year any other info would be a help (wiring ect)
  16. E

    80hp Johnson seaking

    " Ok guys, heres the deal this " Ok guys, heres the deal this motor over heats if ran at full. I have even tried running it without a thermastat in it and tried 2 impalers and all the tubes seem to be clear. I droped the lower end and hooked up hose to the tube to check it. It doesn't over...
  17. E

    1976 JOHN ALLMAND COMMANDER INBOARD

    i am new to the inboard game i am new to the inboard game i was wondering if any one out there could tell me how to identify the trans in my inboard boat the motor is a 351 windsor ford crusader i can find no names on the trany i would also like to know if parts are easy or hard to find for...
  18. E

    Interceptor engine ID

    " I have an engine that I am t " I have an engine that I am trying to find some information on. It has Interceptor on it, and the number on the timing chain cover is: NOCE1R420957. I am trying to find out the displacement, year, model, and horsepower. Thank you for any help you might...
Back
Top