Logo
FULL SITE MENU

Search results

  1. N

    1999 130hp throttle & shifter cable replacement

    My top mount shifter is shifting hard, difficult to gently add rpm on the throttle, one cable cover is cracked where it enters the outboard. I assume both cables are original 1999 and salt water use. Any recommendations on replacement? Honda, Teleflex, or other? Thanks for any assistance or...
  2. N

    Thermostat Question

    I know it’s not a Honda but you fellows have lot of experience with outboards and this is a generic sort of question. Friend has a 1996 mercury 50 hp 4 stroke, which is one merc sourced from Yamaha while they developed their own 4 strokes. It a 4 cylinder carbed model, a real nice running little...
  3. N

    2017 Mercury 30hp 4 stroke idle sticks

    Neighbors outboard, used every year, just going in the water and had a problem with idle. It’s in a center console small zodiac, has mercury remote shifter, side mount. It starts and runs great except when I used the high idle lever and let it run in a barrel, run it up to 2500, take lever...
  4. N

    1999 BF130 tilting shaft tube part number

    I can’t find a part number for this, mine is rusty, I cleaned it out and greased it and installed a new cable plus starboard side grease nut 2-3 years ago, now jammed up again inside the shaft. I’d like to find a stainless shaft. It’s the tube inside the tilt tube, threaded on both ends, the...
  5. N

    Good digital tach for 1999 BF130

    What’s a good option for a digital tach- I see references to one called a Tiny Tach? I have an analogue Honda tach but I find it kind of vague for dealing with idle speeds/low speeds of Rpm. I tried my InNova timing light, it does not read accurately when connected to number 1 plug. Any...
  6. N

    1999 BF130 IAC gaskets?

    Was planning to remove the IAC and clean it but having a delay in getting a gasket. From what I see, it looks like a double o ring? So is it reusable? There is also a filter, looks stainless so likely reusable once cleaned?
  7. N

    Battery to outboard cable question

    1999 130hp, moving 2 batteries from stern splash well into the center console. The wire cable feed from the outboard to the battery and a master switch is currently a rectangular shaped double cable that passes through a big rubber grommet in the outboard case. 1. I need to extend this cable...
  8. N

    1999 Honda 130hp- hour meter?

    I don’t have an hour meter on my outboard and am wondering the easiest way to add a simple one that works off my key switch power or some other method that someone might recommend. I’m picturing an LCD type dash mounted or even installed under the engine cowling, pulling key on only power. Or...
  9. N

    Hydraulic Steering Recommendation

    My original (I believe) 1986 cable steering is slipping, I assume the gears are stripped. I’m pulling the boat today to check it out. Prior boat had hydraulic, Sea Star, I liked it a lot more than the old cable system. Cost of a Seastar system is significantly higher than a NFB cable system...
  10. N

    2005 T60TLR Shifter 703 Button broke

    Helping a friend with this outboard, his up down button broke off. How do I figure out which 703 this is to order the part? It’s a right side mount. When I look up parts drawings on line for this outboard, under controls it shows nothing for the shift handle parts. Another question, where...
  11. N

    1996 mercury 4 stroke coils 50 hp

    Carb model 4 cylinder, it’s been breaking down once warm, carbs cleaned, it fouled #4 plug, now has new plugs. Acts to me like a coil breaking down once it heats up. The pee stream is cool, so not overheating? engine has low hours, clean fuel. How do you diagnose a bad coil? Where is a good...
  12. N

    1999 BF130AX HP Telltale questions

    When running/flushing at say 2000RPM in a barrel, I have water coming out of a hole behind the pitot tube? Is that normal? When running in a barrel as per above, I get a small dribble of water out the hose connection, is that normal? You can see I still have the hose connection attached here...
  13. N

    1999 BF130 Idle Problem

    I bought the boat and motor last year, it would quit when at low idle in gear. I put new plugs in and Sea Foam and it worked fine, until now. The motor starts up normal, revs above 1000, then idles down in neutral to around 750 (tach is hard to read and bounces a bit). Motor works fine other...
  14. N

    1999 BF130A XD Overheating Issue

    Finally launched yesterday, engine started and ran fine, but was not pissing water. Tried reving it up and got a little bit of flow, then nothing. Got overheat alarm, managed to get it back on the trailer. The pee hole was clear and I could blow back through the hose with my mouth, backed it...
  15. N

    1999 bf130

    I just replaced my fuel line, tank to outboard, priming bulb, and added a fuel water separator. I'm ready to launch for the first time and when I pump my bulb, I'm not getting any pressure. When I launch, will the fuel pump pull fuel from the tank, or should I be trying to get fuel up into the...
  16. N

    Fuel Line Question 130 HP

    I'm changing out all my fuel lines, the line to the primer bulb and from the bulb to the outboard measures 6.5 MM or 0.26 inches- inside diameter. 1. Any reason why I should not upgrade this to 3/8 inch inside diameter- would the extra fuel volume be negative in any way? 2. To change this, is...
  17. N

    130 HP Gauges/lights

    Engine serial number BEBE1001155, which I am told is a 1999, under my throttle on the console are 2 red lights, what are they for? I don't believe they are Boston Whaler lights, I have a 1986 Outrage 18. Thanks. Don
  18. N

    2002 BF130A XD Water Tube Ring

    I ordered a new part #19253-ZW1-B01, when I received it, it was not the same as the old one. It has a ridge at the top, the old one is about 1/8 inch, the new one is about 3/8's. It won't seat properly. Looking it up on boats.net, that part number is showing up as correct and the pic of the part...
  19. N

    2001 Honda BF130 Impeller and water in the lower unit gear oil

    Outboard new to me in Sep/17, no real maintenance history. 1. My outboard is peeing very slowly, I think I'll install a new impeller kit. 2. In addition, when I drained my lower unit gear oil, I got a very small amount of milky oil, what gaskets should I change to see if the leak can be...
  20. N

    anodes 2001 Honda 130

    I'm waiting on my manual, how many anodes does this outboard have and where are they? Does someone sell a "kit" or do you buy them individually? Are they Zinc? Thanks, Don
Back
Top