Logo
FULL SITE MENU

Recent content by wassajet

  1. W

    Should this gasket be here.

    Hi, The motor i'm talking about is a 1973 6hp.Evinrude Fisherman model #6302S. I've removed the lower leg to replace the impeller and have found that there is a gasket on the impeller housing plate which is #15 on the parts diagram list. On the diagram there is no gasket shown. The only gasket...
  2. W

    Can't move water pump housing cover up drive shaft.

    Hi, I'm trying to replace the impeller on a 1984 2 hp Mariner 2B (m) serial # 6a1-083661. I have removed the lower leg without any problems & have undone the 2 bolts holding the water pump housing cover on. I have also removed the stainless steel sheath that protects the drive shaft.My problem...
  3. W

    What year is my 2 hp mariner

    Hi, I've just purchased a used 2 hp mariner motor for my tender & would like to know what year model it is please. The only numbers i can find on plate on the bracket are 6a1-083661 but i don't know if this is a serial # or model #.All info. on this motor will be very much appreciated thanks.
  4. W

    1980 Mariner 4 a hp gear housing plug question.

    Hi, I have a 1980 4a hp. Mariner 2 stroke outboard,on the gear housing assembly there is a third plug located on the left of the oil level plug (top plug) this plug is stamped ( WASH ) & seems to be a little bit larger than the other two oil plugs. I looked up the diagrams parts list & found...
  5. W

    What mixture please.

    Hi, i have just inherited a 1980 4hp Mariner 2 stroke outboard, i've been told to use 50 to 1 fuel mixture. Would this be correct please?
  6. W

    Made in Japan Mariner confusion

    Hi, I have just bought a used 4hp. Mariner outboard & am having trouble with what year model it is.I'll give the information that i have from 3 ID.plates on the motor...First plate reads...Mariner 4m 6eo s001394 Second plate reads...Made in Japan for international Co. fond Du Lac...
  7. W

    How do i lift motor support bracket?

    Hi, i have just purchased a boat with a 1978 55hp. Johnson outboard model #55el78s .This motor doesn't have a power trim tilt so i have to tilt it by hand.I can lift the motor ok but i have to reach down to the bottom of the outside of the transom to lift up the motor support bracket so that i...
  8. W

    Can i shorten shaft.

    Hi,I have a 55lb thrust Minnkota tiller steer & would like to know if i can shorten the shaft, because if i adjust it to a comfortable steering height which is all the way down, the prop. is very deep in the water & i'm worried about stuffing both the prop. & the shaft by grounding in shallow...
  9. W

    Where to place fuel primer bulb?

    Hi, i need to relocate my fuel tank from the stern to the bow of my 14 foot runabout because after installing a second battery i have too much weight at the stern.What i need to know is can i locate the fuel primer bulb up the front next to where i steer to save going down the back near the...
  10. W

    Yamaha P95 info. please.

    Hi, I have just been given a Yamaha outboard motor.The person who gave it to me has no idea of its history other than it was found in a shed that was part of a deceased estate. The only ID. i have is on the engine cowell it has Yamaha P95 written on it. I would like as much info. as possible on...
  11. W

    Change from transom mount to bow mount.

    Hi, is there any way i can turn the tiller steer on my Minn kota 50 lb thrust around 180 deg. so that i can convert it from a transom mount to a bow mount? In other words the tiller handle will be facing the same way as the propeller.
  12. W

    What size anchor?

    Hi, i have just bought a 3.9mtr. fiberglass runabout & need to buy an anchor for it.Can anyone tell me how heavy an anchor i will require please?
  13. W

    Will this trim tilt fit my motor

    Hi, i have a 1978 55hp johnson sea horse motor model# 55el78s & would like to know if the trim/tilt off a 1988 70 hp johnson will fit my motor The unit has an internal ram system.All advice would be appreciated thanks.
  14. W

    Change where Minn Kota is mounted.

    Hi all, I have a 50lb Minn Kota transom mount on a 4mtr. f/glass runabout & only use it to keep the boat straight whilst drifting in a strong current which is where i fish.I would like to know if i could mount the electric on a secure bracket on the gunwhale of my boat about 1/3 of the boat...
  15. W

    1985 70hp steering problem.

    Hi i have a 1985 70hp evinrude model #e70tlcos with hydrolic steering which seems to have seized up.It was ok the last time i used it which was only 3 weeks ago. Now i cant turn the wheel to the left or right. Haven't had any steering problems before now & no accidents that could have caused...
See more
Back
Top