Logo
FULL SITE MENU

Recent content by mr_johnson

  1. M

    Water Pee Hole

    "Hi Team. Just started my o "Hi Team. Just started my outboard first time in 7 months. Ran for 3 mins (fast idle for some reason)then steam began emanating from the water from pee hole (obviously HOT). Then, no water at all came through and then spits and spats. I am scared some...
  2. M

    Bendix Gear Will Not Rise to Engage Flywheel

    "Hi Team. Bendix Gear Will "Hi Team. Bendix Gear Will Not Rise to Engage Flywheel on my Johnson 1989 2 stroke 110HP outboard. I have replaced battery, bendix gear and spring. Can someone help please? Cameron"
  3. M

    Mounting this electrical thing back onto block of 1989 Johnsson 110HP

    "Ok - here it goes.. thank "Ok - here it goes.. thank s for your patience men! In yellow circle is something electrical that is connected to the starter motor wire. Sorry - I claim ignorance and dumbness. In blue circle is a SS clip that is used to mount this thing onto the...
  4. M

    Starter Motor Earth Connection

    "Where does the Starter Motor "Where does the Starter Motor earth connect to?(circled) . It is the Johnson 1989 110Hp outboard. "
  5. M

    Leaky Ehaust Gases How to Detect

    How can i tell if i have leaky How can i tell if i have leaky exhuast plate gaskets in my 1989 Johnson Outboard? How can I tell if they are leaking gasses back in to the block? It is interesting to note that these gasses will cause an air pocket in the block causing sensor to alarm...
  6. M

    Johnson 1989 Outboard Port Head Cooler than Starboard Head

    "I just took my boat/engine to "I just took my boat/engine to a dealer to have it looked at. They said the Port Head was cooler than the starboard head (too hot to touch) - implying the t/stats and/or release valves are not functioning properly. I am about to remove the t/stat assy...
  7. M

    Linc and Sinc Johnson 1989 110HP

    Can anyone pass on the specs f Can anyone pass on the specs for this please? Cam
  8. M

    Linc and Sync Documentation from Johnson Manual

    I am taking my johnson 1989 11 I am taking my johnson 1989 110HP motor to a dealer and getting a linc and Sinc checked and re-adjusted if necessary. Can someone possibly provide me with the information from the manual? (I used to have this manual on disk but was damaged electronically and I...
  9. M

    Replacing Bendix Gear on Starter Motor Johnson 1989

    I have now received a new bend I have now received a new bendix pinon gear for for my starter motor. I have tried removing existing one but unable to loosen the nut on top of the shaft. Please advise how I am to remove/loosen this nut.
  10. M

    Connecting Trim Guage and Tacho together for Johnson 1989 110HP

    I want to wire up my tacho and I want to wire up my tacho and trim guage fo rthis motor. Any wiring diagrams exist? Cam
  11. M

    Johnson 1989 110HP Starter Motor Not Engaging Flywheel

    "Team, Here is a short vide "Team, Here is a short video - showing interface of flywheel and starter motor.. (Johnson 110HP 1989) http://au.youtube.com/watch?v=FsEzDZeQtno Why am I not able to start this outboard? THe starter does not want to seem to engage the flywheel. Cam"
  12. M

    Starter Motor Will Only Half Engage

    "Team, Why does the spindle "Team, Why does the spindle gear on top of my starter motor only half engage the flywheel? Please help. 1989 110Hp Johnson 2 stroke"
  13. M

    Battery Placement

    "Team, I am thinking of rel "Team, I am thinking of relocating my battery more forward (maybe helm area) for better weight distibution. Your thoughts? Cam"
  14. M

    Removing Throttle Lever Assy from Control Box Johnson 1989 110HP

    "Guys. The trim up switch o "Guys. The trim up switch on my throttle lever needs replacing ( I think ) because I am unable to trim up whilst underway with large payload. The red button(for trim up)on the throttle lever becomes stuck/indented into the throttle assy and I cannot trim...
  15. M

    1989 110HP Johnson Will Not Hold Idle

    What could cause this outboard What could cause this outboard not to hold idle after I return the Fast Idle Lever to it's rest position? Cameron
See more
Back
Top