Hello everyone. I Have a Yamnaha F9.9 SH- 1987 4 stroke that i have rebuilt the carb and am having an issue with. Now this issue was present even before rebuild so iam assumming the issue is something else. Starts first pull -Idle comes up high till it warms up. Then it comes down to idle great...
Hi everyone. I had A problem a
Hi everyone. I had A problem awhile back with engine bogging out when throtling up but corrected that as there was a pinched line on numer 2 carb. Know i may have moved the throtle control rod yoke abit and know i have rough idle and it stalles when i place it in...
Well took the boat out this we
Well took the boat out this weekend and here`s what found. Did a link and sync. Started right up no problem. Then i Took it out for a spin and the same thing BOGGS after 1/4 throtle. So I pressed in the key to hit the choke and then throtled right up and it took...
"Hi I Have a 1976 70 hp Evinru
"Hi I Have a 1976 70 hp Evinrude that was running good but had sat for about 2 years. Rebuilt the carbs and installed a water pump. Bench tested (with water hose) seems to run good in and out of gear. Installed it on a 16 foot fiberglass boat. Here`s my...
"Hi everyone. I know this topi
"Hi everyone. I know this topic was discussed somewere in these forums,but I was wondering if anyone has any knowledge of swapping out the midsection of a later model 70Hp with tilt trim to fit a 1976 70Hp. Is this possible? and what model year would work if...
"Hi everyone. I recently chang
"Hi everyone. I recently changed my outboard engine from a merc to an evinrude. Know i had a tach with the merc is it possible to use this same tach in my dash for the evinrude? Could the merc tach be riged to work with the OMC control harness. The Omc is three...
Hi everyone. I have a 1976 70h
Hi everyone. I have a 1976 70hp evinrude and I`am trying to locate aengine cover seal. Are They Still available? do newer engine model ones fit? Also would a mercury tach which is from a 65 hp 1975 engine work with a 1976 evinrude engine or are they motor...
"Well did my water pump on my
"Well did my water pump on my 70hp 1976 evinrude. Water comes out of the tell tale mod i did. One question when i put the muffs on and run the water. If i start the engine is water supose to come out of the holes on the side or did i install someting wrong on this...
Hi ive got an 1976 evinrude 70
Hi ive got an 1976 evinrude 70 hp can someone post a pic of where to install a brass fitting in the water jaket so the cooling stream can be seen Thanks
"Hi everyone I have an envinru
"Hi everyone I have an envinrude 70hp Model 70673D serial 71185. I got this motor purring after i did the carbs fuel pump and all fuel lines. Now i started it on a stand with muffs. This motor has 2 1/2 holes side by side futher up the back of the motor water...
"Hi everyoneI have a evenrude
"Hi everyoneI have a evenrude 70HP 1976 model. The other day i noticed that the coil leads on the lower 2 cylinders were crossed (3Cyl model. It didnt look right to me so i changed the orientation. Are the cylinders as follows ( Top of engine)cyl 1 Top,cyl 2...
"Hi everyone i`ve got a Evinru
"Hi everyone i`ve got a Evinrude 70hp 1976 motor that was given to me without cotrols. I belive the one it had were power pilot with the red 10 pin connector. Iam trying to get a set on ebay or if anyone has any for sale here. Can i use the newer version of the...