Hi
I took off the air intake muffler and in the process disconnected two small pipes which connect to this muffler. Both ends of both pipes are now loose.
My book doesn't show them. Anyone know where they go?
Hi - My engine died out at sea with fuel starvation . The eng check lt came on.
The harbor entrance leads to the open Atlantic so this is not a good thing.
When I got back I checked the fuel suction pipe an the mesh filter, the pipes , anti siphon, replaced the main filter/separator and the one...
I have searched the threads but aint got no satisfaction.
The engine is sticky getting back to neutral. It has new cables and lever.
I have the book but not much on this switch. It does close circuit when pushed by hand per book test, but not in actual use when shifting.
Idle speed is good...
Anyone tried this variant on Joe Reeves' procedure. I couldn't get a good result on Reeves with my 200 OceanPro, because disabling Quickstart was not as easy as advertised.
Even when hot ( or grounding B/W p/pack cable), the QS still always works while cranking OR for the first 5 seconds each...
"The 1998 200 oceanpro has lost some power and no longer gets over 3750 rpm or so.
I replaced the plugs and filters - the plugs looked normal-ish. It starts, idles and runs great except wide open
I'm not sure about the full throttle advance screw which I may have lost position in an earlier...
"I am struggling with setting
"I am struggling with setting up new remote+cables and notice this; With throttle cable detached , the throttle does not return to the idle stop after opening it . It seems to be because the advance thing that rotates under the flywheel is quite stiff and the...
"When shifting to reverse, the
"When shifting to reverse, then increasing throttle the revs don't pick up and it finally stalls. This is tied up at the dock. The gear/throttle levers look like they are moving correctly.
Forward is fine.
This after I have been fighting a remote/cable problem...
"Here is the thing. The gear s
"Here is the thing. The gear shift cable has a plastic end fitting at the engine end which connects to the gear shift lever in a 200hp Evinrude ocean pro. The gear shift has been getting very stiff lately and broke the remote.
Anyhow I notice the end fitting on...
"I am trying to identify which
"I am trying to identify which cables and remote I need to replace those on my 1998 Striper/Evinrude 200 ocean pro.
The problem is there appear to be several types.
My cables have at the engine end , plastic extensions with eyes that fit onto projections from...
"Ok the engine end of the gear
"Ok the engine end of the gear cable does not move.
I cant get the side mounted remote off to take a look. The rear of it is behind a panel and can not be seen. There are four screws on a panel aft of the control rotor which come out easy but thats it. Do you...
"When you push the control, th
"When you push the control, the gear shift push rod at the engine end does not move. The shift was very stiff prior.
i cant get the single lever control apart to investigate, although i have removed the 4 visible screws . It is a side mounted concealed cable type...
"This 200 hp evinrude is a bit
"This 200 hp evinrude is a bitch to start if unused for more than a few days. It starts, coughs and dies again and again and you fiddle around with the gas injection, (key switch depress) and throttle and finally it agrees to keep running and is fine.By that time...
Wile t/shooting tacho I see gr
Wile t/shooting tacho I see grey tacho feed also goes to vro.
Does this mean that if tacho signal fails oil injection fails?
What is the tacho feed to vro for?
I have read the tech manual but it doesn't say.
"Here's what happens;-
Re
"Here's what happens;-
Re-launch for winter season.
Starting up, tacho works and batt volts head up to 14v and change
After a few minutes, the voltage reduces to 13.2 and the tacho stops. Subsequent starts, the voltage is 13.2 max. and the tach does not work. It...