Logo
FULL SITE MENU

Recent content by clayvogt

  1. C

    1954 10 hp johnson

    i need to tighten the pivot friction and cant figure out how ther is no friction screw like on my 1956 7.5 hp johnson thanks clay
  2. C

    1954 johnson 3 hp jw-10

    hello when setting the points should i set the gap when the crank key is centered on the point spreader or when the letter o in the word top on lob roller is centered on the point spreader thank you clay
  3. C

    1954 QD 15 10 hp johnson

    motor is still running rough checked inside re-built carb 3 times checked re-buit ignition 3 times. im noticeing black wet gunked up plugs is it possible that the head gasket is leaking water into the spark plugs making it run rough
  4. C

    1954 qd-15 tune up problem

    the motor starts easy but i cant get the idle set it goes pretty low. but i can screw the low speed needle all the way in closed and it does not change the motor i rebuilt the carb new coils points plugs i can spray carb cleaner at the packing nuts and they seem sealed
  5. C

    1954 10 hp johnson top crank seal

    hello i was getting a lot of gunk on my ignition plate and points and coils so i diassembled everything under the plate on the top of the crank the last things there were pieces of an o-ring and pieces of a plastic ring about a quarter of an inch thick about the size of a quarter, probably if i...
  6. C

    1954 3hp jw 10

    does any body know the sierra part# for the lower unit seal ki thank you
  7. C

    1954 10 hp johnson

    hello i replaced coils, points, wires carb kit, plugs,converted to a fuel pump,new fuel lines all in the last week, i can get the motor to start but it runs very rough.i did the 1 and 1ahalf turns on the needle valves to start to set carb and nothing works i have tore it apart and checked...
  8. C

    1970 9.5 hp carb

    hello im rebuilding my 1970 9.5 hp carb and i noticed that on the carb body just to the left of the low speed adjustment needle there is a small hole in the casting i think there is supposed to be like a little lead shot bee bee that is supposed to be there and it is gone can i just plug this...
  9. C

    1970 18 hp johnson fuel pump

    hello i replaced the fuel pump hello i replaced the fuel pump on this motor and the motor wont run unless i keep priming it with the bulb is it possible that im not getting a pulse from the motor any more to run the diaphram pump
  10. C

    1970 95 hp evinrude water pump removel

    hello i bought the motor so i hello i bought the motor so i need to change the impellor do i need to pull the power head like on my older johnsons or not thank you
  11. C

    1977 175 hp johnson carb question

    hello i have a V-6 1977 175 hp hello i have a V-6 1977 175 hp johnson with three carbs that i bought cheap the top carb does not have a choke butterfly only the middle and bottom carb have butterflies is this correct or did the prior owner mess with this thank you clay
  12. C

    90 hp shift rod oring removeal

    hello i need to replace the sh hello i need to replace the shift rod o-ring but i cant drive the brass bushing out of the houseing i have a tapered rod i use on smaller motors to drive the bushing out but it wont budge and im afraid im going to damage the houseing any sugestions thank you clay
  13. C

    90 hp johnson timing

    hello i got finished with my r hello i got finished with my rebuild today thanks to all of you that helped me/ a few more quick questions. rebuilding this motor should have not changed my timing should it. i made sure that the advancement linkage adjustment did not get disturbed when i tooked...
  14. C

    Installing standard fuel

    hello im getting rid of my VRO hello im getting rid of my VRO i bought a standard fuel pump i see the mounting holes on my intake for it there are to screw holes and a port in the middle of them that is pluged how do you get that plug out so i have vacume and pressure to the pump does it screw...
  15. C

    Bolt torque specs

    "hello i have the torque specs "hello i have the torque specs. from my johnson service manual, but there is a torque ranges on some bolts for example lower crankcase bolts 96-120 in. what should you do go to the minimum,mid-range or max. your input is very welcome thank you clay"
See more
Back
Top