Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
TRANSOM
GIMBAL RING KITS
ENGINE MOUNTING HARDWARE
GIMBAL RING KIT
REAR ENGINE MOUNT BOLT KIT
Complete kit to convert the gimbal ring from a spline/splined upper shaft to a
Fits R, MR, Alpha One, Gen II & Bravo drives
square/splined upper shaft. Also can be used to service a square gimbal ring with a
splined steering arm.
REAR ENGINE MOUNT BOLT
Fits MCM I drives (1978‑1983)
GIMBAL RING KIT
1/2‑20 x 5‑1/4 in., Hex head
REAR ENGINE MOUNT WASHER
Fits R/MR/Alpha One drives (1983‑1990)
GIMBAL RING KIT
15/16 in. x 1‑3/4 in. x 11/64 in., Rubber
Priced individually, sold @ multiples of 5
Used to convert standard Bravo gimbal ring to heavy duty gimbal ring and bell
REAR ENGINE MOUNT WASHER
housings. Trim limit switch cannot be used on HD gimbal ring.
Fits MCM Bravo drives
33/64 in. x 1‑3/8 in. x 1/8 in., Aluminum
Priced individually, sold @ multiples of 2
1050