Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
PROPELLER HARDWARE
THRUST WASHER
PROP WRENCHES & PLIERS
FLOATING PROP WRENCH
Fits the following product when used with Flo‑Torq II hub propellers:
Mercury/Mariner 40‑60 hp BigFoot FourStroke
Mercury/Mariner 75‑125 hp 2‑cycle and FourStroke
Mercury/Mariner 135‑275 hp 2‑cycle
Fits 9/16" Nut, Purple (Mercury / Mariner 6,8,9.9 &15 HP)
Force 75 hp (1999) & 90‑1150 hp (1995 and newer)
Quicksilver Branded, Peg Display Product Point of Sale Packaged.
Mercury MerCruiser Alpha and Bravo I sterndrives
Evinrude/Johnson V‑6 outboards 1990 and prior
FLOATING PROP WRENCH
OMC sterndrives V‑6 & V‑8 gearcases 1984‑1990
Honda 75‑90 hp outboards 1998 and prior
Suzuki 140 hp 4‑stroke outboards
Caution should be exercised to assure the correct thrust hub is matched with the
prop in use. Used with Flo‑Torq II & III Delrin (plastic) hub kit propellers.
Priced individually, sold @ multiples of 2
Quicksilver Branded, Peg Display Card Point of Sale Packaged.
THRUST WASHER
Fits 13/16" Nut, Green (Mercury / Mariner 20 & 25 HP) (Johnson / Evinrude
9.9,15,20 & 30 HP)
Quicksilver Branded, Peg Display Product Point of Sale Packaged.
FLOATING PROP WRENCH
Force 85‑150 HP (single exhaust)
THRUST WASHER
Fits 15/16" Nut Orange (Mercury / Mariner 30,40,50 & 60 HP)
Quicksilver Branded, Peg Display Product Point of Sale Packaged.
FLOATING PROP WRENCH
Force 90‑120 HP (dual exhaust)
Fits 1‑1/16" Nut, Yellow (Fits most sterndrives / 4 cylinder & larger outboards)
Quicksilver Branded, Peg Display Product Point of Sale Packaged.
714