Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
STEERING
SEASTAR HELM MOUNT
SEASTAR PRO HOSE KIT
2 hoses‑ 14ft(4.3m)
This kit is designed to mount a SeaStar and SeaStar Pro helm at a 20 degree
angle to the mounting surface. Four possible mountings by varying wedge position.
No helm modifications are required.
2 hoses ‑ 16 ft(4.9m)
SEASTAR HELM BACK PLATE KIT
2 hoses ‑ 18ft(5.3)
2 hoses ‑ 20ft(6.1m)
2 hoses ‑ 22ft(6.7m)
2 hoses ‑ 24ft(7.3m)
HOSE CONNECTION KIT
Allows SeaStar and SeaStar Pro helms retrofit into boats where the following
helms were previously installed: SyTen, pre‑1991 square SeaStar, or mechanical
rotary steering. The kit also reduces helm protrusion by thickness of dash.
FRONT PIVOT MOUNT OUTBOARD CYLINDER
Connects 3/8 in.(9.5mm) diameter copper tubing to SeaStar Cylinders (using 3/8
in.[9.5 mm] diameter nylon tubing.
HOSE CONNECTION KIT
FRONT MOUNT OUTBOARD CYLINDER (STANDARD)
Connects 3/8 in.(9.5mm) diameter copper tubing to SeaStar Cylinders (using
SeaStar Outboard Hoses)
300