Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
REMOTE CONTROLS
CONSOLE MOUNT REMOTE CONTROL-GEN II
CONSOLE MOUNT REMOTE CONTROL-GEN II-W/O EXT
New Design. Designed for MIE inboards & outboards without power trim control.
Furnished with single trim switch in handle for simultaneous dual engine trim and
All installations require an Ignition/Choke assembly and Throttle/Shift Cables to
trailering & individual fine tuning trim buttons in cover. Applications require Throttle/
complete the installatioMust use Gen II Throttle/Shift Cables design. (897978A__)
Shift Cables to complete the installation. Must use Gen II Throttle/Shift Cable
8‑9.9 4 Stroke engines 2005 and newer will use 896145A series and 8/9.9/
design.(897978A__)
generation change above S/N OR192772 and 15/20 4 Stroke will use Gen II series
The power trim extension harness also needs to be ordered separately:
(84-881125A 1= 4 pin Molex to traditional Mercury 3 blade P/T
T/S Cablen.
connector).
Fits MIE inboards & all current Mercury/ Mariner outboards (without power trim)
(84-865772A02 = 4 pin Molex to the Packard 3 pin P/T
and 1993 and newer Force outboards 40 hp and higher utilizing Mercury style
connector)
Fits all MCM and Mercury/Mariner 3.4L outboards with external trim cylinders. Ref
CONSOLE CONTROL- DUAL
CONSOLE MOUNT REMOTE CONTROL-GEN II
Designed for dual MIE inboards & outboards without power trim control. All
Use with Mercury Outboards or Mercruiser
installations require an Ignition/Choke assembly and Throttle/Shift Cables to
complete the installation. Must be used with the Gen II Throttle/Shift Cable
CONSOLE REMOTE CONTROL-GEN II-DUAL
design. (883719A__ or 897978A__)
Fits MIE inboards & all current Mercury / Mariner outboards (without power trim),
and 1993 and newer Force outboards 40 hp and higher utilizing Mercury style
cables (without power trim). Ref 877700A1 or 88688A86
JET DRIVE REMOTE CONTROLS
Must be used with Sport Jet due to the design of the jet drive. This is
due to strength and mounting requirements. Any substitutions must
meet ABYC/Coast Guard standards for mini jet boats.
SIDE MOUNT REMOTE CONTROL
Furnished with single trim switch in handle for simultaneous dual engine trim and
trailering & individual fine tuning trim buttons in cover. Comes with 2 ft.(.60 m) trim
harness with the traditional 3 blade Mercury connector. Applications require
separate Ignition/Choke assemblies and Throttle/Shift Cables to complete the
installation. Must use Gen II Throttle/Shift Cables design. (897978A__)
Fits all current Mercury/Mariner outboards (with integral trim) and 1993 and newer
Force outboards 40 hp and higher utilizing Mercury style cables (with power trim).
Forward or aft cable entry. Accepts 40 series shift cables.
Fits Sport‑Jet 175 and may be used on 90/95/120 applications with Remote
Control Conversion Kit 850698A 1. Also fits 200 OptiMax, 210 & 240 EFI Jet
Drives.
US Quicksilver Product Guide
273