Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
REMOTE CONTROLS
SIDE MOUNT REMOTE CONTROL
SIDE MOUNT REMOTE CONTROL
For manual start models. New design with soft grip. Ref throttle / shift cables
Has a 15 ft. (4.58 M) harness and no trim function with Amp connector and will
897977A__
direct connect to the engine models below without the use of an adapter harness.
Ref. Throttle/shift cable Gen I ‑ 897977A__. Throttle/Shift cables (896143A) for
Fits Mercury/Mariner 4/5 and Mariner 8 to 55 (2 cyl.)
MY2005 and newer 8/9.9 FourStroke outboards. 8‑9.9 4 Stroke engines
generation change above S/N OR192772 and new 15/20 4 Stroke engines will use
SIDE MOUNT REMOTE CONTROL- 8 PIN AMP
Gen I series T/S Cables
Used on MY2005 and newer, 8/9.9/15/20 hp. FourStroke outboards with electric
start and non‑trim. Gen I cable must be used with this control
SIDE MOUNT REMOTE CONTROL-14 PIN
Has a handle mounted power trim switch and a 15 ft. (4.58 m) harness with Amp
10‑pin connector and will direct connect to the engine models below without the
use of an adapter harness.
Ref. Throttle/shift cable Gen I ‑ 897977A__. Throttle/Shift cables (896143A) for
MY2005 and newer 8/9.9 FourStroke outboards. 8‑9.9 4 Stroke engines
Has a handle mounted power trim switch and a 15 ft. (4.58 m) harness with 14 pin
generation change above S/N OR192772 and new 15/20 4 Stroke engines will use
Deutshe connector and will direct connect to the engine models below without the
Gen I series T/S Cables
use of an adapter harness.
Used on MY2005 and newer, 8/9.9/15/20 hp. FourStroke outboards with electric
Ref. Throttle/shift cable Gen I ‑ 897977A__. Throttle/Shift cables (896143A) for
start and power trim. Gen I cable must be used with this control
MY2005 and newer 8/9.9 FourStroke outboards. 8‑9.9 4 Stroke engines
generation change above S/N OR192772 and new 15/20 4 Stroke engines will use
SIDE MOUNT REMOTE CONTROL
Gen I series T/S Cables
2006 ‑ 25‑ 300 HP 4 Stroke Any engine that has the 14 pin connector from the
Has a handle mounted power trim switch and a 20 ft. (6.1 m) harness with Amp
primary harness. Gen I cables are required with this control
connector and will direct connect to the engine models below without the use of an
adapter harness.
Ref. Throttle/shift cable Gen I ‑ 897977A__. Throttle/Shift cables (896143A) for
MY2005 and newer 8/9.9 FourStroke outboards. 8‑9.9 4 Stroke engines
Has a handle mounted power trim switch and a 20 ft. (6.1 m) harness with 14 pin
Deutshe connector and will direct connect to the engine models below without the
generation change above S/N OR192772 and new 15/20 4 Stroke engines will use
use of an adapter harness.
Gen I series T/S Cables
Ref. Throttle/shift cable Gen I ‑ 897977A__. Throttle/Shift cables (896143A) for
Used on MY2005 and newer, 8/9.9/15/20 hp. FourStroke outboards with electric
MY2005 and newer 8/9.9 FourStroke outboards. 8‑9.9 4 Stroke engines
start and power trim. Gen I cable must be used with this control
generation change above S/N OR192772 and new 15/20 4 Stroke engines will use
Gen I series T/S Cables
2006 ‑ 25‑ 300 HP 4 Stroke Any engine that has the 14 pin connector from the
primary harness. Gen I cables are required with this control
270