Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
PROPELLER HARDWARE AND ACCESSORIES
HARDWARE KIT
PROP NUT KIT
Adapts Mercury 30‑60 HP Black Max, Trophy Sport & Vengeance propellers with
12-835467 1 Front thrust washer, 13-42351 1 Continuity washer, 12-31211A 3
Flo‑Torq Reflex Hubs to fit Tohatsu 40‑50 HP engines. Kit contains both forward
and aft washers.
Mercury/Mariner 70 HP+ (non Flo‑Torq II)
Priced individually, sold @ multiples of 2
PROP NUT KIT
Quicksilver Branded, Clamshell Package Point of Sale Packaged.
PROP NUT KIT
Mercury/Mariner 30/40 HP (1989 to present), 50‑60 HP (1991 to present, excluding
Bigfoot), Force 40‑50 HP (1995 & newer), Force 70 HP (1991 & newer), Force 75
Kit includes locking prop nut, 1.5 in. washer, 1.5 in. cupped belleville washer & 1
HP (1996). Rubber hub propellers only. Purchase this hardware kit to complete
13/16 in. spacer.
install of a rubber hub propeller when propeller hardware is not included with
For use with HD (Heavy Duty) 1 1/4" propshaft when installed on Mercury Racing
engine.
200XS, 225X, 2.5 EFI, 225 Pro X, 250XS, 300X, Sport & Torque Master
Priced individually, sold @ multiples of 2
Gearcases (not Fleet Master) and MerCruiser Bravo One XR, XZ & Sport Master
Sterndrives. Tighten propeller nut to 55 lb‑ft (75Nm).
Quicksilver Branded, Clamshell Package Point of Sale Packaged.
PROP NUT KIT
PROP NUT KIT
Tab washer and Nut
For Aft‑Installed Rubber Hub Props: Fits Mercury/Mariner 70‑140 (Inline 6 cyl.
Mercury/Mariner 75HP and up and Mercruiser Alpha and Bravo I sterndrives
1977 and newer), Mercury/Mariner 60 HP BigFoot and 75‑125 HP (1987 & newer)
Quicksilver Branded, Clamshell Package Point of Sale Packaged.
2‑cycle outboards, Force 90‑120 HP (1995 & newer) 2‑cycle outboards.
Priced individually, sold @ multiples of 2
Tab washer and nut
Quicksilver Branded, Clamshell Package Point of Sale Packaged.
Mercury outboards 75 HP and up and Mercruiser Alpha and Bravo 1 sterndrives
Mercury Branded, Clamshell Package Point of Sale Packaged.
US Quicksilver Product Guide
131