Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. Re: 1965 75 hp Electramatic Lower Unit Shafts Stuck After Rebuild

    Are the forward / reverse gear assemblies in the right spot ?---The reverse gear has the roller bearing assembly on the hub.-----These electric shift units are very simple in my opinion.----
  2. Re: 1965 75 hp Electramatic Lower Unit Shafts Stuck After Rebuild

    How did it run for you last year ?-----It would be easy to figure this out , but I can not see / inspect the parts.
  3. Replies
    8
    Views
    127

    Re: Evinrude 28 SPL Running Rough

    The electric primer is a valve.----When you push the key in , it opens and the fuel pump then put fuel directly into the airstream through this primer valve.----This fuel bypasses the carburetor and...
  4. Re: 1965 75 hp Electramatic Lower Unit Shafts Stuck After Rebuild

    Your location ?----Any rust inside the gearcase?-----
  5. Replies
    2
    Views
    12

    Re: 92' 25hp Mercury fuel issue

    Gasket correct between the carburetor and block ?----Lower crankshaft seal leaking ?
  6. Replies
    8
    Views
    47

    Re: BF5A leaking 'something' from breather

    The lower cowling on the motor has " pads " on one side.----This indicates how the motor is to be laid down for storage.
  7. Re: How do I disconnect shift linkage on my 2011 Mercury F30ELPT

    You might have to remove cowling -----Turn propeller while shifting and observe linkages up top.
  8. Replies
    13
    Views
    90

    Re: Johnson commercial outboard timing specs

    I am going to be blunt again.----You are overthinking.-----There is nothing different about commercial motors.---Often just the lower unit / no oil injection / no electric start either on some ( even...
  9. Re: How do I disconnect shift linkage on my 2011 Mercury F30ELPT

    I think you will say----Wow, ----" is this ever easy when you get the lower unit off "-----Just my opinion.
  10. Re: 1981 Evinrude E15RCIS 15hp Won’t start unless cycled without spark plugs first.

    Stop.----You should not have to go through all that.----Put it on a stand.----Remove 4 wee screws and take top of the air intake silencer.----Pull choke on and verify that flapper is actually...
  11. Re: How do I disconnect shift linkage on my 2011 Mercury F30ELPT

    There may not be a shift linkage to disconnect.---Many mercury shift shafts are splined.----Go ahead Look at some U-TUBE videos for clues.---You are about 7 hrs away.---I agree on the robbery part.
  12. Re: How do I disconnect shift linkage on my 2011 Mercury F30ELPT

    Your location ?----That shop must be busy or they have no competition.----Just 45 minutes or less for that job.----Hour and a half at most if it is a fresh water motor.----I think I have to move to...
  13. Replies
    2
    Views
    20

    Re: Driveshaft Shim Spacing

    Have you considered using something called -----" Mechanics blue "----Or " permatex bearing blue "----A simple paste to allow you to check tooth contact on gears.----With time and patience you can...
  14. Re: 75hp 3cyl 2 stroke backfires from exhaust no power

    I would be pulling the exhaust cover to inspect pistons / rings.----About 20 bolts and easy if it is a fresh water motor.----Perhaps you got a free motor with more issues than you might think.
  15. Replies
    5
    Views
    57

    Re: Crank seal rings

    Fact-----Inspect them for wear.-----Some will argue as always.-----What I do on these is chamfer / break the sharp edge to allow them to move easily in the block.
  16. Replies
    13
    Views
    90

    Re: Johnson commercial outboard timing specs

    Some will argue.----In a factory service manual there is no mention of different timing for the V-4 ---" commercial " models.-------And about the only thing different on the commercial model is that...
  17. Re: 75hp 3cyl 2 stroke backfires from exhaust no power

    Check all wires are going to correct terminals.----How did it run for you last year ?----Did this problem develop suddenly ?
  18. Replies
    9
    Views
    60

    Re: 1986 Johnson 90HP

    I can not see, hear or feel your motor.----Is it running with VRO oil injection in service ?-----Regular fuel pump mounted in the proper place on intake manifold ?-----Running on 50:1 mix...
  19. Re: 1995 130HP Johnson 2 Stroke shutting down

    What trouble shooting was done to lead you to believe--- " It must be the carburetors " here ?-----Did you find anything wrong or dirt in the carburetors ?-----Start with a compression test , post...
  20. Re: Early 70's Johnson 70 HP outboard no power on max throttle

    Well--- the carburetors are also the " oil pump " for your motor.----You have to make sure they are clean.----So take the carburetor apart for inspection.----No fuel gong into one cylinder also means...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4