Logo

Search:

Type: Posts; User: makomark

Page 1 of 4 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    4
    Views
    43

    Re: 2006 5.7L mpi rich exhaust

    if they share a common fuel tank (or if two tanks, they both shared a bad batch of fuel), both engines could develop the same situation...

    still believe getting a scan tool and verifying engines...
  2. Replies
    7
    Views
    102

    Re: Crusader 8.1 - Racor gauge readings

    its not the anti-syphon valve itself, its the pressure drop they can induce that is the source of the potential problem...you can just substitute a plain hose barb fitting for testing, if you want to...
  3. Replies
    4
    Views
    43

    Re: 2006 5.7L mpi rich exhaust

    injectors may be leaking and need recondition....

    would be good to get a scan tool and make sure the other sensor inputs are within expected range, too...
  4. Re: Through Hull Exhaust too loud at low speeds

    2X on the diverter...and hoping your Y pipe is still installed....

    You may find some original Silent Choice on fleabay....i know hardin sells some packaged deals too...
  5. Re: Mercruiser 8.2L 2015 HO - Hard starting issue

    I'd be inclined to do the voltage drop tests for starter concerns....
  6. Re: 1988 mercruiser 3.0 with 2000 mercruiser carb and distributor in 2000 model boat stumble off idl

    Mercruiser only offers one cam for a given (rated HP) I-4 engine...they set the timing where they want to when optimizing the engine for its application...
  7. Replies
    1
    Views
    27

    Re: Volvo penta 200 coolant flush

    draining the coolant warm is usually the best bet....

    The HX usually has a drain plug for the coolant but you have to pull the block plugs to get the majority of the old coolant out.

    If you...
  8. Replies
    2
    Views
    31

    Re: Distributed For 270

    On the intermittent issue - you might want to consider 'reality'...you harnesses are damn near FOURTY years old along with a lot of the ther 'support items'....may need to start replacing these...
  9. Replies
    2
    Views
    31

    Re: Distributed For 270

    If you have factory assembled engines, you can look at the serial number plates to determine their <crankshaft> rotation. again, in the factory configuration, the distributors can be swapped between...
  10. Re: Sherwood P 1014 failure again Crusader 350

    Wow, I thought they would last longer than that...
  11. Replies
    14
    Views
    130

    Re: Rochester Inlet Leak Quad

    so, would you say the nylon washer resolved the drip?
  12. Re: 1989 454 ,fuel pump stops after 5 sec., oil pressure sw is new

    If you are referencing the fuel pump, it could be a ground issue....but...I'd check to make sure the ignition system is still working after the engine dies.

    I don't believe there's any relay in...
  13. Replies
    90
    Views
    28,519

    Re: Old Crusader O&M Manual

    should be in the inbox...
  14. Replies
    4
    Views
    71

    Re: 350 MAG MPI computer questions

    with the key ON and the engine OFF, the MIL should be ON....

    Does the MIL go OFF after the engine starts?

    as far as 'switch problems' go, there are only a couple inputs to that ECU...get the...
  15. Re: prep and paint for a welded aluminum boat

    I'd go with awlgrip....plenty of prep documentation on the www, too...
  16. Re: Sherwood P 1014 failure again Crusader 350

    Sorry to hear about that ....

    Did anybody take the bad pumps apart to see what failed?

    I'd think they could be rebuilt and stashed in case a repeat occurs...I'd store them with the impeller...
  17. Replies
    7
    Views
    102

    Re: Crusader 8.1 - Racor gauge readings

    The pressure drop is more than the spec value....I'm guess the values are the max pressure drop and they occur at WOT?

    what is the pressure drop at your normal cruise RPM?

    Did you leave the...
  18. Replies
    5
    Views
    115

    Re: Ignition problems

    if it starts ok and the ECU connects to the distributor, I don't believe I'd mess with the jumper...would be a good idea to make sure the advance function works though...
  19. Replies
    14
    Views
    130

    Re: Rochester Inlet Leak Quad

    18 ft * lbs is pretty snug for the larger nut....I'd suspect either side of the gasket surface for the fuel inlet nut - and make sure the body of the carb (where the fuel inlet nut threads are) isn't...
  20. Replies
    11
    Views
    123

    Re: Am I Crazy to Ask This?

    depends upon how much boat you are talking about and what your expectations are...

    Honestly, there are a lot of clean used boats for sale at reasonable prices...it would be more effective to buy...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4