Logo
FULL SITE MENU

Recent content by ML_MCM

  1. M

    97 Evinrude 115 HP Air Mix Idle screw size???

    9/64" allen wrench is the answer
  2. M

    97 Evinrude 115 HP Air Mix Idle screw size???

    Can someone verify what the size/head is for the Idle/air mix screw that is in the throttle body of the 115hp Evinrude E115GLEUA - 0342775 - Needle Valve ?? I've seen posts that say it is a #2 PoziDrive. I've read 9/64" allen wrench. Also M20 Torx. Tried some allen wrenches but either had...
  3. M

    97 Evinrude 115HP - Starts but stalls

    Pulled apart the VRO last night just to make sure there was nothing obvious prior to testing it and I believe I had installed the O-Ring prior to the Air Diaphragm when I rebuilt it originally. I reassembled it properly and seems to run great now. Just need to put it in the water and see what...
  4. M

    97 Evinrude 115HP - Starts but stalls

    I'm in New Hampshire. Ran from aux tank. no change. Compression 125 psi in all cylinders. Carb bowls do not leak as best as I can tell. Pumped primer until solid looking specifically for bowl leaking. I was going to check the pulse line and try and test the VRO with a vacuum/pressure tester...
  5. M

    97 Evinrude 115HP - Starts but stalls

    racerone, You've been a help previously, any thoughts on my updated status to this issue? I'd rather not go pre-mix if I can help it so hoping I can get past this fuel delivery issue Thanks
  6. M

    97 Evinrude 115HP - Starts but stalls

    Update#2: rebuilt all the carbs with OEM no change even though I used it a couple times before this happened I was going to draw gas from clean new fuel container went to drain the bowls and there was no fuel in them. started it up and was able to keep it going by pumping the primer bulb every...
  7. M

    97 Evinrude 115HP - Starts but stalls

    Update: Had some electrical issues that I got resolved so now back to the issue of this post Here is what I know Spark on all 4 plugs 125 psi on all 4 New plugs and after running for a few minutes only 2 showed signs of firing (bottom cylinders) Was able to rev up for a minute or so and all 4...
  8. M

    97 115 hp key switch/ignition strange behavior

    While troubleshooting a fuel issue(another thread) I ran into an electrical problem that may be the original problem and it went from bad to worse. It looked like I wasn’t getting spark on 2 plugs ( top on starboard and bottom on port). Pull it out of the water and into the garage. When I went...
  9. M

    97 Evinrude 115HP - Starts but stalls

    Update: Carb rebuild kits were not good. Seats were slightly different size, gaskets were cheap and flimsy and I had a hard time getting the floats where they needed to be. Vapor pump kit great. Instructions. Went smooth Got it all put back together and it idled great and I think I could have...
  10. M

    97 Evinrude 115HP - Starts but stalls

    Found the instructions. Thanks so much
  11. M

    97 Evinrude 115HP - Starts but stalls

    Do I have the correct PN for the repair kit? 0393088
  12. M

    97 Evinrude 115HP - Starts but stalls

    So I bought a gasket #27 and the diaphragm. Is there a rebuild kit for the vapor pump? I see rebuild kit for a fuel pump that has gaskets that look like the ones in the vapor pump. 0393088 part number. Are thes gaskets interchangeable? Also does anyone have a breakout of this vapor pump? I...
  13. M

    97 Evinrude 115HP - Starts but stalls

    This is the float/needle valve I'm talking about
  14. M

    97 Evinrude 115HP - Starts but stalls

    I'll try and give as much info as I can with this issue.... After the winter, motor started right up and used it a couple times with no issue. Ran great although coming back to the dock stalled when I go to idle. Went to go out again a few days later and starts and stalls. If I try to throttle...
  15. M

    97 Evinrude 115 hp E115GLEUA prop shaft question

    Thanks for the response. I'll try some heat and give it another go. May end up scrapping this thing but not quite there yet
See more
Back
Top